hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I have just installed VS Code and was following the videos for building an application. My board does not show up on the nRF Connect tab connected devices. The status bar...
Dear Members,
I can use a simple timer in :
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fnrf_dev_simple_timer_example.html...
I use my customized antenna board (5 antennas on it) with the following IQ problem:
DF3 CTE[0]: samples count 45, cte type AOA, channel index 13, slot durations: 2 [us]...
HI
I am using nrf52840 and I want to merge nrf_calendar and app_ble_uart example, added ssd1306 oled 128x32 spi and mpu6050 as well,
but the error is from nrf_calendar...
which version of embedded segger studio do i have to download from the link ? www.segger.com/.../ ----> i am new for embedded-studio , so when i browse to the download page...
I'm getting an error NRF_ERROR_NO_MEM when trying to initialize the LPS22HB, and the RTT log shows:
The line being triggered is in nrf_twi_sensor.c, line 151, which is...
I'm stuck with trying to install Nordic/ANT+ SoftDevice SS340-SD-v6.1.1 on the Adafruit Itsy Bitsy NRF52840. Within nRF Connect - Programmer, I am getting the following error...
Is it possible to use a NRF9160-SICA-B1 for a pcb designed around the NRF9160-SIAA-B1? Based on my findings, the pins are compatible, I just want to make sure I'm not missing...
My nRF52840-DK stopped working. When trying to connect using nRF Programmer v2.2.0 I get the following in the log:
15:45:05.011 Using @nordicsemiconductor/nrf-device-lib...
Hello,
just recived this kit, I ordered it some time ago but were no stock.
Problem is that software doesn't detect the hardware under "SELECT DEVICE". The device has...
When flashing files from an iOS device I run a lot into data size errors (not always), when using the same files on Android they can be copied without a problem.
It looks...
Hi,
I built a ble_app_buttonless_dfu_pca10040e_s112 project on the nRF52805. However, I cannot receive Bluetooth signal on nRF connect.
I have attached my generated hex...
Hi,
In an application with a nrf52840, we measure the frequency by counting rising edge with PPI linking GPIOTE EVENTS IN and TIMER TASK COUNT
GPIOTE.EVENTS_IN -> PPI...
Hello everyone,
I created my first own layout design and the antenna. Before I order the PCB I hope you guys can review it one time. I tried to get the most informations...
Hi all.
As per subject, I'm unable to follow device using PCA10040.
Everything was set according the latest documentation available ( infocenter.nordicsemi.com/.../nRF_Sniffer_BLE_UG_v4...
