I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello,
I am using a nRF52840 dongle to communicate between a laptop running Ubuntu and a phone running Android.
Right now I set up a UART-BLE communication using an...
Hi
I've been developing using an NRF52 DK and have moved onto my own design board, I have one small problem which I'm unable to replicate using the DK. On my own board,...
I have tried to study the behavior of the QSPI and the external flash. I noticed that the QSPI_CONFIG_READOC and QSPI_CONFIG_WRITEOC settings in sdk_config.h cannot be set...
Hello,
I'm developing AoA/AoD feature, accoring to manual, the nrf52833 uses S0CONF and S0MASK to automatically determine if the part S1 exists in the packet or not. I tried...
Hi everyone,
We are designing a low power PCB based on the nRF52840 BLE. At the moment the device is advertising with an interval of 1s and a timeout of 3min (advertising...
Hi everyone,
I am looking the ble_app_template_pca10056_s140 example and I have a question regarding the advertising_start(erase_bonds) function in main();
When you call...
Hello,
We are in the final stages of our product development and we would like to add a feature used during assembly to give some sort of confirmation that everything is...
Am trying to evaluate the nRF9160 + nRF52840 combo as in the thingy, we want to send an sms to the device and reveice back its GPS location. SMS is spectically requested for...
Hello,
I want to prevent a scenario where I successfully perform a DFU with a faulty firmware image. I have a bootloader that handles firmware updates both for the NRF5...
Hello all,
I am working on low power sensor development with nRF52833 as target. I have some questions but I'm not sure it this was addressed in some other posts.
1. I...
Hi,
I'm integrating some c++ code using ble_app_uart example as base. The code has some cout << "text"; kind of outputs that seem to go to uart by default configuration...
Hi. I'm trying to find out the real consuption of the nrf52832. I have two questions after consulting part "7.2.1 CPU performance" of the datasheet.
1- Is there a difference...
Hello,
I have recently used the new toolchain manager to upgrade to ncs v1.3.0. Now I am using Segger Embedded Studio to flash an nRF9160 with the at_client sample. My issue...
Hi ,
I have an Android app that acts as a Central mode and Nordic nRF9160 as peripheral mode.
Once the connection is established , App will read the characteristics...
Dear all,
Pushing the hardware to the limits, I came up with a question about the architecture of the microcontroller itself: Can two different instances of SPIM start...
