Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
new to nordic and keil need help compiling custom project
currently my main file only works with the nordic 1822 series processor and in your example.
I need to have it...
I cannot find a specification for the SAADC converter's reference accuracy. The product specification indicates it is 0.6V, but beyond that I cannot find anything. Looking...
Can we run our Customised Bluetooth Host Stack on nRF5340.
Please provide us with sample Brinup Code for Bluetooth Controller.. Send HCI Reset and Bringing up the Controller...
We need to retrieve data from an FPGA to the nRF5340, process it with the network and Wi-Fi protocol stacks and then send the data to the nRF7002 for Wi-Fi transmission. We...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
i'm trying to read voltage signals from a sensor using internal ADC.When the input is not connected,there will be noise. I use differential input pins like this:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL...
Hi,
i need to store few configuration bytes in non volatile memory. I found out there is settings module that can be enabled in Kconfig GUI (SETTINGS option).
My use is...
Hi,
I have successfully programmed the nRF5340 Audio DK as a gateway device using the Command Line Tools and by using the directives listed in the 'nRF5340 Audio' program...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and have run into an inconsistency I'm hoping...
I have an application where I need to trigger time critical SPI reads of accelerometer data (sample rate is very crucial and data is fed into a FFT). In my current SDK based...
Hello!
I have added a UART and I2C to the Mesh Sensor Server example and on a custom NRF52840 board everything works fine.
Today I tried to add SPI without success.
...
1. Hi currently i am using nrf52840 sdk ver 17.1.0 s140 sd we have added UART in the secure bootloader/ Bootloader_ble_debug
2. we can able to send multiple bytes once ie...
I am trying to interface my PDM mic (ICS 41351) for a week now , and only got erros . Please direct me to a simple Project Code to use PDM mic with my nRF52840
Hello,
I am working on unidirectional voice broadcasting device where the maximum range is the priority. At this time I am developing on Audio DK boards.
I need some help...
Setup
nRF9160-DK
PCA10090 1.1.0 2022.4
Modem FW: mfw_nrf9160_1.3.3
Asset Tracker V2, I tried both the downloaded version from here: https://www.nordicsemi.com/Products...