I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello,
I am using the nRF51 transmitter_pca10028 example to try to communicate with legacy systems using nRF2401A.
I could achieve nRF51 TX to nRF24 RX successfully...
I would like to burst out 12 packets of 64 bytes and then go into RX mode immediately after for a single payload, followed by another round of transmissions. Is there a shortcut...
The data is sampled at 3khz, each sample is 2 bytes, connection interval is 7.5ms ,4packets per connection interval. The data is displayed on a graph with respect to time...
When I execute nRF5x_MDK_8_7_1_IAR.msi from the SDK 11 directory the files from the .msi are added to the IAR install directory, not the SDK. These changes are ignored when...
I was little bit confused between NRF24l01 and (+) plus version which is better . i want range of 900-1000m. which is best??
If i choose NRF24l01+ what are the ways to...
(/attachment/0495424521df76d5b8f8e66c969ed791)Hi,
I add ANCS Service into my Heart rate ref ble_app_ancs_c example code.
I use MCU nRF51 and SD130 in nRF5_SDK_11.0.0_89a8197...
Hello,
My device is based on nRF51822 SD110 v8.0. Softdevice is enabled, but no BT functionality used. I measure 2 different voltages with ADC each second with two channels...
I'm writing code for PCA10040 basing on UART/NUS example. There are no big changes: different UUIDs and just one characteristic for both reading and writing. I can connect...
This is a follow-up question from devzone.nordicsemi.com/.../
I finally got passkey support to work on ble_app_uart but don't quite understand the changes made to the code...
I am trying to add static passkey pairing to ble_app_uart in SDK_11 s130. To do this, I first implemented static passkey successfully in ble_app_gls using sd_ble_opt_set(...
Tl; dr
I tried to use OTA DFU with Public BLE Address, but I failed. Is this possible?
Details
Condition
I modified ble_app_hrs example like below (SDK11, pca10028...
I have a radio board using a NRF51822 with a custom radio protocol. I need a unique identifier, ideally 24bit, 32bit but be acceptable.
I notice in the parameters there...
I've looking through as much of the documentation I as I could to read more about the radio timeslot api.
I looked through the SDS document and the chapter on the Radio Timeslot...
I am able to use eclipse to run simple project, but after move the real one, getting lost of errors:
www.dropbox.com/.../Screenshot 2014-04-02 09.10.41.png
I add required...
