Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
When initially starting Sidewalk on BLE it seems that the current consumption is high if you start with only LINK1 enabled. It seems that perhaps this is due to the SX1262...
I am using Wireshark 4.4.0 and Nordic nRF Sniffer for Bluetooth LE 4.1.1 (nRF52840-Dongle PCA10059). In Wireshark I see a device, a peripheral, sending advertising packets...
hey, I am using nrf52840 in that i am making it compatible with DFU by using sdk2.8, but getting this error
C:/ncs/v2.8.0/nrf/include/flash_map_pm.h:47:22: error: 'PM_mcuboot_secondary_ID...
hello!
I am currently using the nRF7002DK to implement the examples from nRF dev academi. I am practicing based on lesson 5-exercise 2.
lesson 5 exercise 2
In the example...
Hello, I want to make my project DFU OTA compatible, so when I tested on development it works fine once I created my pcb using nrf52840 module in it. So it is taking huge...
Hello,
I have a question regarding a recent issue.
I'm currently developing with the nRF52840 IC or EVM, and I'm facing a problem. Whenever I write firmware to the flash...
Hi Team,
I recently purchased 2 Audio DK's and I set one up as a gateway and the second as a left headset. I was able to pair the two, stream audio from my PC through the...
Hi,
We are currently developing a BLE device (HW and SW) using the NRF52811.
As we want to be able to update the device via FOTA we need to have the Bootloader to have...
Hello,
I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
Hi All,
We're going through BQB certificate with our mice, and we're informed that test get failed because new rule will be implemented in May 2023.
Our Chip is NRF52833...
Hello,
I want to use external flash. I did some research on the subject. I am using SDK 2.6.1. I have a few questions.
1- Does the spi_flash example I examined work on...
I have a custom nRF9160 board running a modified asset_tracker program. I am using UART0 as a command line interface for testing and debugging. I can enter commands to setup...
Hello. I'm trying to do spi communication on a custom board with nrf5340 used. I'm using three threads, I build it, but if I put it on the board, the board will have a problem...
Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
Hello, I get a compiler warning when I try to log a float value using the LOG_INF macro in my project. The code I'm using is from the cell-fund course: lesson 6, ex. 1. Toolchain...
