Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I have developed a custom board for the nrf52840 with the QFAA QFN48 package.
I am trying to program it with my nRF52840, I am using P20 of the DKconnecting the...
I am wondering if someone can help point me to a repo that explains how to create a gpio interrupt that can detect when my CS line goes from High to Low and jump to a method...
I'm evaluating an OpenThread mesh network in a large warehouse and considering the nRF21540 Front-End Module (FEM) for the router devices. To test this setup, I purchased...
Hi,I have been trying to configure two I2S devices where I will read data from mic SPH0645 with NRF5340 then I need to send that data to Amplifier(TAS2563).So,help me configuring...
Hi, I have a question regarding the operating voltage range of the nRF5340. I found that it can operate between 1.7 and 5.5 volts. However, can we restrict the minimum voltage...
Hello,
I am developing a BLE keyboard. I am using SDK17.1.0 and nRF52840. The part that is stuck is multi-pairing. I need to develop a function that alternately connects...
Hi Team, I am currently working with the nRF52833 BLE module, and I’ve noticed that the BLE device takes approximately 16 seconds to reconnect after a disconnection from the...
Hello,
I bought a NRF52840 USB Dongle for evaluation purpose (bigger project in mind).
I cannot even run the demo from NRF Connect (like BLE or RSSI viewer)!
On my...
I'm encountering issues while building my project with custom boards. Each board has a corresponding *_defconfig file with specific configuration options, and I also have...
Hi all，
Using the default sid_end_device demo without any modifications, using the default hello selection with nrf52840dk.
I downloaded the Alexa app, started Sidewalk...
Just for fun, I thought it'd be interesting to see how to implement a delay on the nrf52840 using the least possible power.
For any long period of time, you should use RTC...
Hi all,
I am trying to develop an application that frequently gets location info using gnss and also needs to work with battery.
In the Product Specification v2.2 I found...
I attempted to run the "peeral_hr" example under NCS2.4.0 and used nRF21540-EK to enhance the signal, but in reality, there was no significant change.
I attempted the following...
HI ,
I set PA / LNA in the following way. I found that when the device is connected, it will be disconnected and will no longer be connected. How to set PA / LNA correctly...
