Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
I am following the steps to configure the Bluetooth BE Sniffer in Wireshark, but I am having difficulties. I tried both on Windows and Untuntu (Linux).
Setting up nRF Sniffer...
I am interfacing MAX30003 with Nordic NRF52DK (NRF52832 SOC). The Nordic successfully generates SPI CLK and writes the register data to the MOSI pin. But, the MAX30003WING...
Hi,
Ours is a battery (LiPo) operated device with VDDH= 3.0 to 4.2V. One of the reasons for using nRF52840 is to avoid an expensive external DCDC IC. But due to the Anomaly...
I'm trying to follow the DevAcademy Intermediate Lesson 5 Exercise 2 using an Elegoo shield instead of the Adafruit one.
The shield I'm using is this one: https://www.elegoo...
Hello, we have built a BLE device based on the 52840 chip and the nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_mouse example architecture. We have built a...
Hi,
1. The customer would like to know which values are configured for which registers of nRF5340 by the following instructions?
nrfjprog --family NRF53 --coprocessor...
Hello!
I am using an nRF52805 for a custom board design and I am hoping to get some advice on selecting peripherals and Zephyr features that would best meet my system...
Dear Nordic
hardware:NRF5340, sdk:2.6.1
Our project needs to use floating-point calculations. Attempting to add CONFIG_FPU=y and CONFIG_FPU_SHARING=y to prj.conf will...
I use GNSS with the timout at 0 and interval at 65535.
I do not really need the location but is it nice to have a kind of a log of it because it is available en power consumption...
Context: We are planning to connect the nRF9151 to a private test network using a coax. cable. for development debugging.
(#1) Do your modules support SIM cards with test...
Good day
I have a lwm2m client running on a custom nrf9160 board. I would like to run everything network related to network on a separate chip. Assuming that the two chips...
Some guidance on this query,please. I have a project with several freestanding application (please check topology below). I would like all the apps to acccess a custom board...
Hi,
I am currently configuring the nPM1300-EK with the nRF5340-DK by following the instructions from the webinar "Adding battery charging and fuel gauging to your nRF52...
For a device like the nRF9160 Feather, you need a second USB to UART device for listening to the modem traces. When I go to select the Terminal Serial Port under Advanced...
Hi All,
Im very new to this how firmware space and would love some help.
Currently i have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
