Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Dear Nordic,
I'm unable to register an nRF9161 device on the Verizon Thingspace IoT Network. They have a web UI which allows one to enter an IMEI, ICCID pair. When I enter...
Hi,
We have developed firmware for a custom broad using the nRF52832 with 512kB flash, and our firmware currently uses 48.5% of the flash.
We are using Zephyr and version...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I would like to know more about the TLS 2K packet limitation in the nRF Connect SDK.
Is there a way to not be constrained by this limitation. I've seen some posts about...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I am following the link;
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson...
Hi,
I'm hoping you can help.
I am using the CENTRAL_UART and PERIPHERAL_UART to evaluate the nRF52840, and using a terminal program works fine.
What I want to do is...
Hi all,
I have a problem that seems very simple, but I cannot make sense of it.
I have a simple setup on the NRF52840 DK that senses a rising edge on pin 1.00 and...
I am trying to write tests for my code using CppUtest. I know the platform has memory leaks detection support. it seems that everyting is set up correctly to see the results...
Hello,
I am starting with the nRF Connect. I got a nRF52840 DK and I am following the 'nRF Connect for VS Code' YT series.
I got as far as part 5 (debugging), but I cannot...
Hi all,
SDK: NRF Connect v2.5.0 We've made a custom PCB with the NRF9160, and we have made a custom board configuration for it.
Our issue seems to appear when trying to...
Hello,
I have a mosquitto broker running on my pc. I want to connect and published to this broker through nrf9160.
The issue that I am facing is that prj.conf file only...
I want to use RTT log to output some data, but the data is output. 6 bytes in a line, but the first byte is an independent line, and the next 6 bytes are a line, staggered...
I would like to enable and configure the high power mode on the DC to DC converter in the nRF52840.
I am looking for the device tree source entries and the necessary entries...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.6.1 SDK: v2.6.1
I am developing with the nrf7002, and my current setup involves using a Samsung A54...
