Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi,
I encountered some problems when using UARTE.
In terms of hardware, I have connected the 52840DK LOOPBACK_PIN_1A and LOOPBACK_PIN_1B.
Software code is the original...
Hello,
I see that kiss_fft is used in the libLC3 library. I would like to use it for another part of my product in addition to the pre-compiled LC3 lib, but don't want to...
I'm pretty new to embedded development/electronics and I'm trying to interface with a I2C pressure sensor, but I can't seem to communicate with it. I'm using nrf52840dk board...
Hello,
Up until today I had been developing fine with visual studio code, installed via Toolchain Manager. Then, I clicked "Pristine Build" for the first time in a few days...
I installed the VSCode extension for nrf connect.
I want to do the build on this page:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/thread/tools.html...
Hello Team,
example: SPI master_slave advanced non -blocking
i just open nRF connect sdk example in vs code and build it
I am getting below error while build
Please...
Hello,
I am trying to play with zephyr networking samples on my nRF5340 + nRF7002 EK devkit board.
I am using NCS 2.7.0 release SDK. i was able to build and run some Wi...
I'm not sure if zephyr questions can be also asked here. Problem I am struggling with is approtect mechanism to prevent flash readout. I am trying to use Zephyr config files...
Hi,
I am currently developing a custom Zigbee end device with support for FOTA updates. My FOTA seems to work (all data gets transferred correctly) but the update won't...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hello,
I build the ZBOSS NCP sample from NCS v2.6.0 for the nRF52840 dongle. I use the optimization flag -O2 (for speed) in the build configuration (VS Code NCS extension...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hello,
I am uploading my code with a basic URI to be advertised by the chip.
I am able to build and upload the code for the nrf52832 in my nrf52 DK, the program works...
Hello Team,
I am using nrf52840 board which supports ZIGBEE . Setup Details: Zigbee_LIGHT_BULB (nRF52840 DK) Zigbee_LIGHT_SWITCH(nRF52840 DK)
Light Bulb Example
I am...
