Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I am using NRF52833 and trying to setup DFU specifically for OTA.
As experienced in other threads the size limitations are there
Secure_Boot builds creating slot partitions...
Howdy guys,
I am using an nrf52840 and SDK version 17.1.0 alongside Keil. I just upgraded from using the arm compiler version 5 to 6, which required me to switch from the...
Hi,
I have an implementation in which two boards communicates through ble and i want to measure the throughput of both. The behaviour that I see is that increasing the connection...
Hi,
I have a Tuya FingerBot Plus and when using the Zigbee Shell sample:
1.I can 'click' the finger using a ZCL command
2. I can't change the 'finger mode' from 'click...
Hello
I have 2 devices ,a central and a peripheral on a custom nRF52840 board
Using Zephyr SDK 2.5.0
The distance between the devices is 10.9 meters. When TX power on...
Hello,
We have nRF52833 on the custom board, now we want to do DFU over Bluetooth. During my initial research reults with following questions:
If you use 1. " nRF Connect...
Hi, Everyone
I have space constraint in my round PCB for RF section where i have take referance from thingy91 board and choose the same components exept mcu is nrf5340 claa...
Hi,
I have a request to port an old code into Zephyr. The code uses a proprietary protocol and the radio has been developed on bare metal under a nRF52832 chip. There is...
Hi all,
I am evaluating ANT+ features in nRF52 DK board and I am using nRF5_SDK_17.1.0_ddde560 SDK.
I need to implement ANT+ Bicycle light profile (LGT) in my device....
Hi.
I'm developing a ble module now.
I have a question about time out, interval among BLE init Advertising.
As shown in the picture below, time out (in units of 10ms...
Setup:
nrf52840DK (Zigbee Cordinator based on Zigbee Coordinator sample)
nrf52840DK (ZED)
NCS v2.4.1
Hi,
I am working on Tunneling cluster handling as that one...
Development environment: ncs 2.6.0.
my application need BLE-DFU, so i added multi-image support to my project.
the pm_static.yml is the typical default system configuration...
Hello,
I am working on a SWD flasher for nRF52 chips. I try to perform basic commands like flashing a firmware or reading flash content. I wanted to use FICR informations...
I am using NCS V2.6.0 and using zephyr there is no examples to measure battery level using saadc we can measure the battery level right? I used LEDs to indicate battery level...
