pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi all
In nRF52840_PS Pin assignments sheet, some pins Recommended usage is " Standard drive, low frequency I/O only ", does that mean only low frequency (up to 10kHz...
Hi,
I am writing an application that reads data from the I2S interface, adds it to a queue and sends it via BLE (the code I have implemented so far is added at the end of...
Hello,
I am using the 802_15_4 MAC api to configure my device as a coordinator.
After it has been configured as a coordinator I want another device to connect to it...
I am using nRF52805(SDK 17.0.1 & S112) in my application development. Designed GATT Table Having some custom services with read, write & notify properties, And also, there...
I am testing advertising mechanism of nRF52832 device. But the following error occurred.
app: sd_power_system_off() failed, errCode=0x2006
The following is log messages...
It appears that an incorrect value is being used as the reset handler address so that the jump from bootloader to application is to the wrong address.
I am porting a bootloader...
I can not program the NRF52840 with the programmer software on windows 8.1. However when I run a virtual machine in oracle virtual box using windows 10 it works. I would rather...
Hi all
I have two units, one acts as Central and the other one acts as Peripheral.
I erase chip of one of the units, and then always failed to pairing, with a BT_SECURITY_ERR_PIN_OR_KEY_MISSING...
Hi,
I'm writing an app that creates a CSR, has it signed by a (web-)server and subsequently uses it to authenticate to another (mqtt-)server. For the CSR generation and...
I am trying to port a project to an NRF52810. The project uses a bootloader with a modified transport to work with a proprietary RF protocol. The bootloader/app works on the...
II have a question on how to automatically activate the change from “minimum BLE advertising interval” to “maximum BLE advertising interval” after (for instance) 30 seconds...
I'm unable to use the PSA crypto methods when OpenThread is enabled on NCS 1.9.1. Linking fails with undefined references to PSA crypto methods.
To reproduce, us the nrf...
hi，
i have just to develop an appilcation with NCS 1.9.1 of nrf52840. Now I have tried to activate DFU and I had to realize that the image size is too large（490k without...
I have a design that had previously only used Serial communication to talk to the NRF52840 and did not use the USB interface. For this coming design we want to use the USB...
