In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi
I try to use in a mesh topology. I decided to send a string from client to nodes and receive its response. but I don't know how apply that. please help me to choose an...
hi , we have a nRF52840 DK when connected to PC via J-link there LED5 blinks . when i try to flash the code using Kiel IDE
get this error
using nRF connect the device...
Hello DevZone,
On my board I have a nRF52810 and a nRF52840. I want to implement a serial bootloader for the nRF52810 and have the nRF52840 program it.
I have looked...
Hello All,
We've got a new design using the nRF9160 - most of the PCBA's are connecting just fine to LTE-M - but I've seen a few with 'erratic' connections to LTE-M - I...
Hi, I can successfully build the openthread-cli sample but fail with all matter samples
Please refer the following log
> Executing task: nRF Connect: Build: light_bulb...
Hi
I'm just starting out to test the nRF9160 DK board and have just flashed the NB-IoT Asset Tracker as per the introductory video uploaded by Nordic here:
https://www...
I use a nRF9160DK for make my experiments:
nRF9160(modem) -> mdm_1.3.2
nRF9160(application) ->Serial Modem LTE (nRF SDK 2.0.0) with UART 2 and CONFIG_SLM_NRF52_DFU_LEGACY...
Dear Support Team，
Based on NCS 1.9.1, compile and download Hello Word firmware to nRF5340-DK (1.0.0), measure the voltage of all IOs with a multimeter as shown below: ...
After I ported my project to ncs2.0.0, I found that the RX of nrf9160 could not receive data. To this end, I modified at_client for testing and found the same phenomenon....
Hi All,
Later I will build a Custom Service, so I refer to ble_app_blinky.
According to the image below, I cannot clearly understand the difference between the two from...
I recently encountered a MCU crash problem. I think it is related to NRF_ LOG_ Process (). I used the simulation to catch the following scenarios. MCU crashes at this time...
Hi all:
SDK17.1.0
softdevice:s112
example:ble_app_hids_keyboard
I add a lot of function in my project ,including gzll, i2c,timer1 ,app timer ,rtc ,flash read/write...
Hi,
We are troubleshooting high power consumption on a custom nRF52832 board. It has taken us down to just
1. Enable RTC,
2. Setup GPIOs,
3. With and without NRF_POWER...
I am currently experiencing an issue using MCUmgr CLI over a serial connection provided by the on-board J-Link debuggers on nRF52 devkits.
When using MCUmgr CLI to send...
