In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Is there any zigbee example for nrf52840 dongle (PCA10059) ? If not, what is additional changes needed to add support in existing examples?
I unable to run the zigbee switch...
Hi, I need to add Azure IOT connectivity to nRF5340DK. I have already tested NodeMCU based data upload to HTTP based server and successfully working. Now, to divert the data...
I am trying to upgrade SoftDevice and Application firmware from v6.1.1 to v7.2.0 on Nordic USB840M dongle and I am facing a strange issue after such upgrade.
Please find...
Hi,
I have created my own service and charecteristic
1. But i am seeing only unknown service - How to give a name to this service
2. I am getting unknown charecteristic...
Hi
I have compiled (successfully) the Zephyr example samples/bluetooth/peripheral example for the nRF52 DK (nRF52832).
I am going through the code and trying to understand...
Hi
I have developed a device using the nRF52832 and I am wondering if there is built in functionality to reset the chip back into bootloader mode without programming the...
Hi All,
I'm using SDK17.1.0 and I have a question about mobile device subscribe.
I asked this question before, but the engineer didn't reply, so I asked again, thank...
Hi All,
I want to port BPS to my custom project, I encountered the problem as the title.
When I connect and trigger the subscribe like this picture.
My project will...
I have code that runs for around 5 days, then for some unknown reason hangs or stops running, which makes it almost impossible to debug.
I have also tried to implement interrupt...
Hi.
I have an issue that, If I power off Master and do save flash at Slave side together, the nrf_fstorage_is_busy(p_fs) return value always true .
When BLE is connectting...
I added a mesh shell module to my firmware running on nRF52480 .
Opened the mesh shell
uart:~$ mesh init Mesh shell initialized
mesh provision 0 0x100 0
Crash (see...
Hey,
I have implemented BT FOTA process for my zephyr based application. DFU over Bluetooth works fine. But now I struggle to implement manual upload of image (it will be...
Hello Devzone,
My name is Ted. Recently I posted here and received some good help on low power sample code for the nRF9160DK board. This code helped me prove in real life...
I'm currently trying to set up a simple demo using 2 dev kits running the SPIS and NRFx_SPIM examples but the SPIS seems to always send corrupted data over the MISO line....
Hi,
I'm using two dev kits to test out some SPI firmware before I deploy it to our custom boards and I've been running into a weird issue where my SPIS sends out corrupted...
