In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi, i have a problem with nrf mesh. nRF5_SDK_17.0.2_d674dde
nrf5_SDK_for_Mesh_v5.0.0_src
nRF52-DK(PCA10400)
Android 6 and 10.
Bluetooth 4,1 4,2 5.0.
I use example...
When using USB with CONFIG_NO_OPTIMIZATIONS=y I'm getting a usage fault and Zephyr gives the reason K_ERR_STACK_CHK_FAIL. The fault looks like it occurs in the unnamed thread...
Hi,
In case the FMFU fails or the device gets into some recovery state. Is there a way to get IMEI without enabling the modem library? When the modem is in process of failed...
Hi,
Can you please tell us how to send Hex data using AT#XSENDTO command ?
I am using the "Serial LTE" application. In the old SDK version (v1.6), it was possible to set...
Hello,
I recently saw this post: https://devzone.nordicsemi.com/f/nordic-q-a/71940/low-power-mode-using-saadc-with-ble_app_beacon and I'm interested in the example for measuring...
Hello Kenneth,
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2...
Hello,
I try to port project from IAR to Segger Studio. I followed the guides for porting projects like this and this . So, I did:
- Imported IAR project to SES with internal...
I am using nrf52833dk and download nRF5_SDK_17.0.2_d674dde when i build the code the code the following error occur
asBuild target 'nrf52840_xxaa' compiling SEGGER_RTT_Syscalls_KEIL...
I have an "old" nRF5340-DK which I use to program an external board I am developing. I have no problem with the J-Link/SWD connection to my external hardware using the J19...
Hello Sir,
I will use Nordic nRF52 series(832 or 840) to develop smart bluetooth device. As I need to store mp3 audio files in external flash and then will play mp3 audio...
Hi,
In our use case we act as a peripheral and a phone is connected. We transmit lots of data using a protocol on top of the Nordic UART Service. All data is sent using...
Hi,
I have two questions as below. Thank you.
1. Oversampling + burst mode only can use on one channel, can't support two or more channel. Is it right?
2. If Q1's answer...
HI,
We have developed our product with nRF52805 chip using its reference design (Dongle).
Can i use QDID ( 138610) for my end product certification for Bluetooth SIG?...
Hello,
for some days now, my modem is unable to connect to the network, it gets stuck in searching and i don't know why?. I am using an eSIM card from iBasis and i am trying...
