[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi there,
Could you please tell me the exact part number of nRF9160 and nRF52840 on Thingy: 91?
I cannot find the specific information even though I looked through the...
Hi All,
How many nodes can connect to a node in ble mesh network. I go through code in ble mesh, but i did't found the answer.
Can any one please tell me.
Regards
...
We have an application using SDK for Thread 4.1. The application requires sending large custom commands over CLI.
We increased the size of NRF_CLI_CMD_BUFF_SIZE in sdk_config...
Hi, I am using the nRF connect app to test the BLE function on my code. I am able to scan the device and Service UUIDs just fine. However, when I click on the "connect" button...
Hello,
I have been trying to implement the tinycrypt ECDSA algorithm for our product. I had sampled the implementation in a sample project with ECDSA being the only implementation...
Hello I am working on an application which is based on the ble_thread_dyn_mtd_coap_cli_pca10056_s140 example. I then used the ble_app_rscs example so that I could add Bluetooth...
Would it be possible to be talked through the steps of setting up SPI with the nRF52833DK using the Zephyr RTOS? I am new to the Zephyr RTOS and have so far been unable to...
Dear BLE mesh experts,
This is how the provisioning screen of my Android app looks:
The intention is to enable the user to provision various unprovisioned ble mesh devices...
I am reading through the code and would like to understand the following macro
#define DRV_RTC_INSTANCE(id) \ { \ .p_reg = NRFX_CONCAT_2(NRF_RTC, id), \ .irq = NRFX_CONCAT_3...
Hello!
In the description of the usb module, I found the registers: NRF_USBD-> DPDMVALUE, NRF_USBD-> TASKS_DPDMDRIVE and NRF_USBD-> TASKS_DPDMNODRIVE
" State D+ and...
Hello,
I have been writing to my nRF9160 for the past few weeks now, no issues. My board was working fine yesterday. I left it on overnight to see how much battery it...
Info:
Windows 10
Segger Embedded Studio V5.20a
SDK16.0.0 & Mesh SDK 4.1.0
nRF52840 & nRF52832
I'm setting up a friend node and a low power node. The friend node...
Have used nRF Connect V3.30 for the past year to program nRF52DK with USB and nRF52832 BLE modules with Segger J-Link Base programmer without issue. Updated programmer app...
