Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
Right now, I am trying to open that example files in SES IDE. But I couldn't open.
I kept the file location like as
D:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\peripheral...
I am trying to integrate cli over Nordic UART Service. i want nus control over command line interface such as PuTTY or Termite.
How to solve this and what files should be...
I have two NRF52832 boards. I cannot get the SDK to compile so I'm going at it barebones style.
Transmitter Board code:
Receiver Board code:
The receiver board never...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
I use nrfjprog in a CI system (on Windows 10) which has multiple NRF52 boards attached to it. The boards are all run in parallel with the -s parameter to nrfjprog and the...
Hello, i have an issue with softdevice API combined with timeslot API. I use timeslot API to scan for packets one time (one time interval) with 30000us. Then before timeslot...
Hi, I'm using mqtt_simple example based application to send BLE tracking data through LTE on custom boards. UART is used for connection between MCUs. Power is ON constantly...
Hi all! Since I do not have a system for updating the certificate when changing the server, I decided to disable certificate verification when connecting to the https server...
Hi.
I am a student studying esb examples with nrf52433 board.
1. If data is sent from ptx to prx using static payload, is tx completed without receiving ACK? Don't need...
Hello,
I try to measure the current of the nRF SoC on my NRF52-DK, by using an oscilloscope and USB as a power supply, related to the guide from Nordic from here:
https...
Hi,
I need to write a 32-bit value to an NVM flash page whenever my code hits an assert failure. This failure can occur anywhere in the code - my application, the Nordic...
Hello,
I'm working on a circuit which has a pin connected to a pull-up resistor, using the nRF52 DK and SEGGER Embedded Studio 5.20 to develop the software.
This pin is...
Hello everybody, I am using Zephyr with the nrf52840-dk device. I would like to store the DTLS credentials with a secure way. I don't want to be part of the code and thus...
I have been testing out HTTPS with the http_application_update .
I have been able to successfully setup a TLS 1.2 connection, but I was seeing a lot of "Peer closed connection...
Hello
I would like to modify my Transmission Parameters of my Thread network. According to the CoAP protocol ( https://tools.ietf.org/html/rfc7252#section-4.8 ), it is possible...
