Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi all,
We have designed a PCB where we use BMD-350 ( which is based on nrf52832 ) , HX711 and the accelerometer ( MMA8452Q ) as primary components. The device is supposed...
I am in the process of integrating the latest SAADC driver into my project and have noticed an issue after adding the errata 122 workaround to my saadc event handler per the...
Thanks in advanced. On sdk17.0.2 examples\ble_central\ble_app_uart_c, I connect a button's one end to nrf52832 pin 24, the other end is connected to VDD. So I have to #define...
Hi,
There is an option CONFIG_LTE_NETWORK_TIMEOUT for the LTE Link Control. The default is 600 seconds (10 minutes) but I couldn't find any suggestions for the timeout and...
Hello ,
Now I am sending the data per 7.5ms in the interval of time over ble .I am loosing the packets , to avoid this I am planning to send the data in the structure .How...
Hi,
I got a unit based on NRF52 (No matter what SDK) which is connected via 1-wire (dallas protocol which is very time accurate) to other unit.
The other unit is the master...
Hi! I wanted to ask someone who knows more than I, if this setup makes sense, and how I could test my design.
A bit of background: We're developing a custom board which...
Hello, I am using nrf51822 / SDK 12.3 / SD 130-2.0.1.
When a normal timer is set and softdevice off, the timer interrupt does not occur.
In SDK 10 / SD 110-8.0.0, timer...
Hello,
I am trying to use the flash API of fstorage in my code. I have called below function at the start of my code. I want to save some integer values every 1 min interval...
Hello
I am trying to read a characteristics from my peripheral using my central. From what I read here, I have to use sd_ble_gattc_read(). Is it correct ? But I did not...
Hello
We have produced boards with a Telit module using the nRF52832 chip.
Our software developper have a lot of problems making the connexion and communication reliable...
Hello,
After a long war trying to connect MPU6050/MPU9250 to NRF52 DK with nrf52832 on board, I finally succeeded and I am getting values through UART.
But I have 3 problems...
Hi,
I would like to get the stored CCCD values of a bonded peer using pm_peer_data_load()
I am currently struggling with the format of the data returned by pm_peer_data_load...
Hello.I am a graduate student at Nanjing University of Posts and Telecommunications in China.My question is, does your company provide the source code of the Bluetooth mesh...
To the kind attention of Nordic support team,
we are doing ble bonding using passkeys.
We noticed that when starting the passkey phase, a ble connection event is generated...
