Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
hi guys, i'm triyng to enter the bootloader mode in my nrf52840 dev kit in order to upload the softdevice s340 fo ant.
is there anyone could help me how to do this?? i'm...
I am trying to compile nrfutil into a standalone executable, following the instructions at: https://github.com/NordicSemiconductor/pc-nrfutil
This works on Linux, and for...
I am working on a device that contains an nRF52840. It is a BLE central with up to 20 concurrent peripheral devices. For user experience, it's important that it be able to...
In certain situations, I and customer are having issues connecting to cell towers. The issue seems to be most consistent when the Link Monitor indicates a signal strength...
Hi, I was confused about the behavior of GPIOTE Handler module。I defined a handler(gpiote_event_handler) and I hope when the GPIO Pin(0.14) is changed from high to low or...
I use the example usbd_ble_uart with SDK_15.3.0. I need to send any byte received from the terminal via BLE. Do not wait until the buffer is full or the end of line character...
Hi,
I am trying to combine the usbd (hid mouse) example with the uart central example to run on the nRF52840 dongle. I am having a lot of problems and am not really sure...
I have some colleagues that are working on a project where they want to use the nRF52 as a general purpose IO processor alongside providing an BLE interface to a host Linux...
I installed SDK 15.3.0 build 59ac345 and started working though the DFU secure boot loader example. In the 15.3.0 documentation it says
Setup
You can find the source code...
Hello
We are using custom board which has two chip configuration for BLE stack. Main MCU runs the Zephyr Host only BT stack in peripheral mode.This is supposed to be GATT...
I am trying to compile the SPI example in SDK 15.2.0 for nrf52810. I am getting a compiler error in SES on nrfx_uart.c:
I modified the project according to the SDK documentation...
Dear all,
Is this possible to flip a switch on the board to get nRF9160 IOs at 3.3v rather than 1.8v ? I have a LoRa module that requires TTL 3.3v UART signals, and it...
Hello,
I believe I have found a possible race condition in experimental_task_manager / task_manager.c, task_events_wait().
The race occurs if a task calls task_events_wait...
