I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hi,
I've been using the nRF24l01+ for some time now and am quite satisfied. I'm having a new issue that I'm unable to explain and for which I would greatly appreciate some...
I have filed an issue related to HCI UART sample from zephyr running on nrf52832. I compiled the hci_uart sample successfully, but I am not able to use the UART interface...
Hello, I'm using SDK 15 and softdevice 6.0.
I use the micro as a master and I connected an i2c sensor as slave. I had put external 10 Kohm pull-ups, but I had a low level...
Hello ,
I am using SDK for mesh, I have saved .hex image file in flash.
Is there any example or any suggestion how can I run bootloader which will read data from flash...
HI:
Always error while porting,Error: L6218E: Undefined symbol app_uart_init (referred from main.o).
I added a path, and ENABLE UART_ENABLE 1 in sdk_cofig.h
Compile...
I have set up the gcc toolchain on Mac OSX to compile my BLE nRF51822 code and I tried to flash the code. Here are the 3 scenarios that I have tried (JlinkExe on Mac)
Case...
Hi,
I am not sure if this is the right place to open up a thread about a zephyr HCI firmware issue. Since Nordic also contributes to zephyr I'm putting up this question...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi All:
When I simulated PWM by GPIO, the output current noise was shown like the picture below (red circle area):
Cause it will lead to a loading issue in the backend...
I want to implement a long write. The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi Nordic team,
I have 2 nRF52840 DK boards.
I followed the steps mentioned in the below link, I am able to Transfer the DFU archive over serial with nrfutil(LED keeps...
I want to enable the Logger Module to have the high default severity of Error and then be able to enable lower level severities on an individual module for debugging. Is this...
Hardware used: 2 nRF52480 DK boards
I am running nRF5_SDK_15.0.0_a53641a\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput example, I want to increase...
