Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi
We are working on a product using NRF-51822 chip. I am new to Nordic SDK and want to know how to use fstorage to save data into flash. Following is code. Sometimes data...
Hi,
I would like to build a project with functions below.
Support BLE uart service
Support CLI with uart interface for the communication with terminal, like TeraTerm...
Hi All, I am building a wireless MIDI controller using the BLE nano v2.0 from RedBearLab.
MIDI is a protocol to control software musical instrument, therefore latency needs...
Hello everyone,
I try to modify SDK 14.2.0 S132 ble_app_template example with Segger Embedded Studio, but I got an error about uart. All uart functions appear to be "undefined...
It seems that the version of the soft device used in the mesh sdk does not match the version of soft device SDK that I can download, and the version used in the mesh SDK has...
Hi,
I am trying to run the examples for the pc_ble_driver_py and I get some issues.
advertising.py says "board not found"
heart_rate_collector.py gives a calledProcessError...
Hi folks,
I want to do a project from scratch using the Segger compiler. Where can I find relevant documents with it. How can I make changes on the Blinky project? For...
Hello,
I have two version of Python 3.6 installed: 32 and 64 bit (Windows 10)
Recently i installed nRF5x command line tools (9.7.2) and pynrfjprog 9.7.1
For Python...
In zephyr many PPI has been employed in radio, and other PPI from 20 to 31 is pre-programmed channels and can not use by application. Do you have any plan for optimize this...
hello,
I have one problem to distinguish the following 2 functions :
ble_srv_is_notification_enabled and ble_srv_is_indication_enabled
in on_write function,
the two...
Hi Nordic
I saw the Dfu example.
BLE Secure DFU Bootloader and Buttonless DFU Template Application. I have two questions here. The boot loader and app distinguish a ram...
I'm getting a weird behaviour on my first NRF52 custom board. It's a BLE with HR, battery and a custom service. After programming I can test it properly with/without debugger...
Hi,
I am using SDK 14.0 on nRF52840 (DK), with sofdevice enabled and FreeRTOS port.
My question reagrds the "blocking mode" transfer - event handler was not provided...
I have four PCA10056 Development Boards and I downloaded the SDK for BLE Mesh. The examples, however, only work with the PCA10040 boards. I have tried redefining the board...
