Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
According to the point above
link text
i bought the thingy but i did'nt think about the jlink ..
you can add me to the advent calendar ;-> for a nRF52 DK because...
I understand that the connection parameters viz. connection interval, connection supervision timeout and slave latency are negotiated between the BLE Central and BLE Peripheral...
We currently have a SPI interface between MSP and the Nordic nRF52840. In the DTM documentation it indicates UART is used to command the tests. Is it possible to do this using...
Hi,
I have 5 nrf52832 and nrf52851 beacon boards. All nRFs working in the beacon mode. They all in the same room. I tring to get a list of the active beacons the module...
Started out with the ble_nus-exmple. Added logging of a sensor to flash, and got it to work in SDK11, even without using the sd_flash*-routines, but writing/erasing directly...
I would like to perform an OTA on the DWM1001 board which has a nrf52832.Where can i get the details an the range that can be achieved with employing ANT.Are there any test...
I am following Tutorial 7 on "Development with GCC and Eclipse" and I am working in the Windows 8.1. I have followed instructions from the tutorial for installing the arm...
hi,
i am using a nRF5240 DK for receiving multiple services and characteristics data from Nordic_thingy_52,to receive and print this data on UART i used sdk 14.2.0's "ble_app_blinkey_c...
Hi there~. I was working on a BLE RC car (BLE peripheral) using Nordic's nRF52832-QFAA MCU , Nordic's UART Service for motor control, and Battery Service (BAS) for battery...
Hello.
The development environment is as follows :
OS : Windows 7 Pro 64bit
IDE : Keil uVision V5.24.1
Python : 2.7
SDK Version : nRF5_SDK_14.0.0
DK : PCA10040...
I want nrf51822 to switch between 2 different advertising timeout. One will set advertising timeout with 20s, another will keep advertising.
Currently, I use following...
I have a server running on my Android phone. I looked at the service UUID encoded in the advert packet using and Wire-shark and confirmed my app is broadcasting packets. ...
I am trying to execute code that broadcasts (uses the Soft Device Ble stack) on target nrf52832 boards connected to the PCA10040.
I am successful uploading a program (that...
