Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I have a program based on some of the examples which runs in peripheral and observer roles. When either role is running alone it works without issue but if advertising and...
Hi,
my task is to develop a "repeater" and I have three nRF51422 evaluation kits.
For example, one of them sends a file, the second one receives it and then sends it to...
Hello,
Using the "simple_uart_get_ with_timeout",I cannot receive a "frame" bigger than 6 bytes.
Why?
while(simple_uart_get_with_timeout(1, &UART_RX[receivedBytes]...
I have a simple app that send button press/release events to a smart phone. One of the buttons doubles as the wakeup button. I would like to qualify the wakeup button press...
The documentation for S110 v7.1.0 sd_nvic_ClearPendingIRQ implies that it works with any valid IRQ.
I find that (using S110 v7.1.0 with SDK 7.1.0):
sd_nvic_ClearPendingIRQ...
Hello,
I'm currently reading nRF51_Series_Reference_Manual_v2.1.pdf. On page 28.9.9 there is the UART CONFIG register documented. Two bits of configuration for the Parity...
Hi,
Tried to develop an application to read current time characteristics from central device (ios app) by using nrf51822 peripheral device(s110_nrf51822 v7.0.0.). After...
Dears,
There is a problem as the subject. I am using the reference code of ble_app_hts to add an app timer for a service. the device of nRF51822 can be searched and connected...
Hi,
I'm really new here, sorry if it is a beginner question.
Our company wants to start developing a RTLS (Real Time Location System) to track mainly person (patients...
There are a few threads on using the AES module and there is a lot of confusing and somewhat contradictory information.
I want to do the following:
generate secure...
Hello,
i have an application that sends periodically sensor data from one sensor network (6 sensors - 16 Bytes) to a host f = 1/4 - 20 Hz.
I read the s210 and s110 SDS...
Hello, I'm using the nRF6310 board and tried the HID Keyboard Application
(S110, ble_app_hids_keyboard) example.
The nRF51 SDK version is 6.1. I use IAR for ARM 7.1. ...
Dear,
We are developing the nRF51822 for an application of BLE device. The timer is the key process in the application. Anyone kindly share the experience with me about the...
I have a test set up using the ble_app_hrs example where I increment a dummy uint16_t periodically and then send that value up to the nRF Toolbox iOS app to plot. I want to...
