In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hello,
I've developed a custom PCB which uses an nRF52810 SOC. I've been developing the software for the device using NRF Connect SDK 2.6.1 in Visual Studio Code, and I...
The first time I download the program to my device , it will cause a crash when I try to set NRF_POWER->GPREGRET for OTA purpose;
However after restarting my device, and...
I've found an interesting behavior in the less with the Copy button on this step:
I found that if I clicked on the copy button, the spaces in the text are 0xA0, but if...
Hello,
I have enabled the BIS gateway to send stereo signal, and the BIS headset can receive the stereo signal and play it.
Now I can pack the left and right data to one...
I implemented MCUboot in Serial Recovery mode on a custom USB stick to enable firmware updates via MCUmgr. Initially, everything was working correctly, and the image transfer...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our project needs RSA to exchange secure data.
I use example "samples/crypto/rsa",...
I am working for 2 years on nrf_sdk with softdevice and FreeRtos on cpu nrf52832
now we want to move to Zephyr OS.
- I installed nrf command line tools. nrf connect for...
We're using the Nordic Zephyr library (SDK v2.5) to configure the nPM1300. Using the library, the battery discharge current limit is set to 1000mA. However, using a logic...
I am trying to make my gateway send stereo data to the headset where it will be played on an external codec. I want this to be a single stereo stream.
I had this working...
Hi,
I was looking into hooking up an SD card to the nRF9160DK that I use for data collection during evaluation and early stage pilot projects. I noticed that there is an...
Describe the bug
BLE pairing on the new NRF54L15DK does not succeed. Connecting and advertising works, only pairing fails. I have tried the same example on the NRF52840DK...
Hi, we are using custom PCB with nRF9160.
we are writing a firmware for radio test lab. We are using LTE asynchronous in our firmware and LTE-M mode. We want the modem to...
Hello.
I am using the nRF5340 DK.
According to the circuit diagram, it seems that when I apply power to VBUS_nRF, there should be no power on VDD_nRF of the MCU.
(Power...
Hi,
for my custom device with nRF52840 and nRF Connect SDk v.2.8.0with VScode I want to add bootloader so that I can pass firmware to it through USB cable. I want a simple...
Hi, Good day!
I have been trying to change the SDK version for the past few days, but I am unable to open the Manage SDKs or Manage Toolchains tabs....
