In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Could you pls advise what control is there over the output voltage on PPK2?
For example, the STM power monitor only supports discrete output voltages such as 1.8V, 2.4V...
Dear Support Team,
I'm trying to test 802.15.4 feature with the precompiled radio_test hex file, but got an error when connecting the CLI through PuTTY. Below is the detail...
I am very new to the Nordic line and I have an nRF5340-DK that I would like to build a basic BLE Remote Control project. The Remote Control must pair with a phone or computer...
Hi,
I am using VS code for my project, which is using bl653 board. While in build configuration setup in vs code am getting this error. ERROR: source directory - does not...
Trying to add UART capability (sample project from console) to a a ESB transmit sample project. Could not get a build assert to work.
1) Tried to add all of the selections...
Hello,
On a BLE Central, how can I enable connect with auto connect to a peripheral with previously saved bonding information.
Once paired and bonded, I can recall bonding...
Hi everyone,
I am updating firmware for mesh using following this commands:
PS D:\nrf5_SDK_for_Mesh_v5.0.0_src> nrfjprog --program .\bin\softdevice\s140_nrf52_7.2.0_softdevice...
Hi everyone. I am writing to have an important info, that is, is it possible to load a .hex file, preloaded in an external flash, to program from my application in the nRF52840...
Hi,
As shown in the subject, I am developing a product which needs to support extern Flash-based BT OTA-upgrade. So w here can I find examples of OTA-upgrade using external...
Hi Nordic
In our product, nRF52832 is connected with another MCU through UART. We find that the overshoot in UART signal is very high.
The yellow one is the TX signal...
Dear All
I am trying connect/disconnect function with the DK, it gives me some reason codes, my app is based on central_multilink, which I cannot find their meanings, could...
Hi nordic in our product nrf52832,guided by the tutorial developer.nordicsemi.com/.../README.html,we find something strange. as we have 3 nrf52832 chips in our product,two...
Greetings,
One query on the very useful eDRx notifications in NB-IoT mode (nRF9160 SDK running 1.3.1 FW, used with MoSh app) :
I have just noticed that sometimes when...
With reference to the following known issue: NCSIDB-114: Default logging causes for nrf connect sdk 1.3.2. Is there any further documentation regarding the workaround mentioned...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
