Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hello,
Is there a way to configure mcuboot to allow updates to the bootloader itself? That feature is supported in Nordic's bootloader, but I haven't been able to find...
Hi All,
We are using NCS v1.7.1 on our custom designed nRF52840 board. We have a touch screen interfaced with I2C to our device. There is one more controller connected on...
I am making a "program that keeps multiple software in Flash ROM and reads arbitrary software according to instructions".
When I open the hex file with a text editor, the...
So i have my nRF5340 DK and have been pretty successful in getting my Mesh working with some Thingy:52 devices, some Adafruit Feather devices and some Sengled Lamps.
Groovy...
I am trying to read from the LIS3MDL sensor using spim on the nrf52840 dongle. I gave the rx buffer with the length of 7bytes. Whenever i tried to read from the sensor, I...
Speaking with various MVNOs, not all carriers support PSM or eDRX when roaming, so I am interested in the time and wattage consumed transitioning from PSM --> to ready to...
Hi,
I want to connect "nRF52840 Dongle" via SPI to an 6-Axis IMU (Adafruit ICM-20649 / InvenSense). The collected data (cycle = appx. 10ms) should be sent out with BLE to...
Hi.
A simply question: i want to get data on " LL_VERSION_IND" control PDU from peer. Example: my device is slave, after connecting to me i want to get LL_VERSION_IND data...
Hi,
When will you release the SDK for the PCA0054 (12 antenna array) with nrf52833DK?
Specifically, code that supports more than 1 tag detection
If full SDK is not available...
Hi,
I have worked on a lot of projects on nRF51/52 devices. But still i do not understand why exactly should we use custom/multiple services for each kind of data (like...
Hello,
Having now finished the BLE and I2C sensor my final stop is the SPI sensor before production. I can rebuild and successfully run the ncs playground example .
My...
Hi, I am working on SPI master-slave application, as in, on one BL653 I am running SPI master driver, I am able to observe the waveforms for clock and data transfer from master...
Hi,
Are BMD-341 and MDBT50Q–U1MV2 modules are exactly the same?
Why I asking this question is, I saw some differences between them in the datasheet especially in the...
Hi all,
I would like to program the nRF dongles and Thingy 52, but i don't know how to choose right development kit to program the dongle and thingy.
Which one is best...
Hi,
We are developing a wireless protocol based upon 802.15.4 for nRF52840 and have some trouble with the MAC layer. To begin with, a mlme reset is requested and then an...
