Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hello,
Im using E73-2G4M08S1C module based on nrf52840. Somehow even when in erased state its consuming a lot of energy and starts heating very fast.
Im trying to figure...
Hi Nordic team
I failed to demostarte multicell location sample.
Hardware: Thingy91
SDK: v1.6.0/multicell location
Modem: v1.3.0
Q1. At prj.conf, nrf cloud location...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hi,
My application is currently using s132 v5.1.0. The Release notes for s132 v6.0.0 say:
"Fixed an issue where incorrect timing calculations during the LE Data Length...
Hello
I am running this version of SES
SEGGER Embedded Studio for ARM
Release 5.34a Build 2021011401.44914
Nordic Edition
Windows x64
When I run my program in...
Hello,
I am using the pine watch hardware, to do some tests,
I configured through the overlay file, the I2C_1 to use pins 0.6, 0.7 as shown below,
&i2c1 { compatible...
Hello,
I'm playing with the timing subsystem in order to measure some execution time with higher granularity than the RTC tick on nRF52840 (using PCA10056 DK).
I'm specifically...
Hello sir,
I am using nrf58232 Dev kit board in which when my BLE goes is in advertisement board and after couple of seconds advertise APP_ADV_DURATION is expired then it...
Similar, unresolved issue can be seen here .
I just got my official nRF52840DK and setup nRF Connect on my MacBook. I'm able to build the Blinky example and flash it...
Hi,
I have the following in my code to measure throughput over the Nordic Uart Service.
It works, but I was wondering if I am measuring correctly. I took this measurement...
Hello all,
I'm working on a BLE central application based on nRF Connect SDK V1.6.1. The application connects to certain BLE peripheral devices and does a service discovery...
Hello,
I have been building an application using the CLI and I am thankful for the CLI example and how well it works. I am wondering is it possible to use the CLI but...
Hello, Im using SMP over UDP (OpenThread) and after updating to v1.6.0 in NCS, sending most commands with `mcumgr-cli` makes the device restart with:
This happens for most...
We are currently experiencing malfunction with the big chip on nRF9160dk board, which provides USB-UART and jLink functionality. After 30 minutes, to a few hours, we either...
