Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
The Attach LTE is working but i can't use some command AT for testing Data, as you can see in the screenshot below, i tried with somes commands but it's failing, can you please...
I think the figure 10 in nRF9160_PS_v2.0.pdf chapter 5.1.3.1 is worng.
R and C should be swapped.
It is different to Figure 118 chapter 10.3.1 R2, C10.
Exist a list...
Hello,
I have the following problem. I am using the SDK for Mesh 4.2.0 with the nRF5 SDK 16.0.0 on the nRF52840 DK, I am using the sensor model and I have extended it with...
Hi,
I want to make a BLE Multirole application where the central demands LESC, bonding and MITM and peripheral connections is JUST WORKS bonding.
Is that possible? If...
I'm trying to modify the flash_fds example to write a start time when a button is pressed, then an end time when the button is released. I get the time over TWI from an RTC...
Hi, We are into Commercial health devices using nrf5340 and looking to use AoD technology for our device to get its indoor location. We need to have a Receiver with antenna...
What are different options to load the soft device on custom board? Currently, I am using nRFGoStudio to load the softdevice on nRF52840 DK. We will not have segger hardware...
My app uses a proprietary service and characteristic UUIDs; the app needs to completely manage all characteristic reads and writes. With nRF Connect, I can see my service...
Hi Community,
For community's help I success to create 12.3.0 DFU version get work.
So now I try to make all hex(softdevice, bootloader, application) to one hex file...
Dear Nordic,
We are trying to figure out the difference between the working/feature set of nRF_crypto file and mbedtls.
Which one is better and why?
Ambimat
Hello,
I wanted to ask which uart library we have to use in SDK16 and which configuration to have a LOW POWER UART
We are in development phase on the devkit PCA10040 and...
Hi guys,
So i have some Nordic DK board including some dongles, NRF52840 DK, NRF52833 DK running with Zigbee and thread SKD 4.1.0 and make a mesh out of them. But I have...
Hi,
I have to control 16 pin output pins based on the 16 pin interrupt.
Is it possible to have 16 pins interrupt in nrf52840 . Pin change interrupt
when i config
...
I use SDK 15.3, nrf52840.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/setting-up-the-timeslot-api
Normal use most of the...
We are developing a new product that requires extremely low power consumption with a target to run advertising intervals of between 2 to 10 seconds.
We are using the nRF52805...
