Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello everyone
I success in compilation gpio basic example but I have some problem about bluetooth mesh example.
It show message "undefined reference to `bt_rpmsg_platform_init...
Hello!
I've only used the DK board so far, so I've rarely used an external debugger.
I'm going to use a custom board later, so I'd like to learn more about how to use...
I just both the board, and I can get the 4 LEDs and the NFC to work; I have followed all the instructions but unsure what is going on - and suggestions?
1.nrf9160 module abnormal reset, no abnormal reset log information, I would like to get modem related log submitted to you for further analysis, but I do not know how to use...
I use nrf5_SDK_for_Mesh_v420 on four nRF52 DK board, one is client, the other is server. But I fond, the light_switch_client example is used to control two server board, now...
Hello,
I am using the Light switch example for BLE meshing. I am trying to provision the nRF52832 with Raspberry Pi. I am unable to successfully provision because of the...
Hello!
I have created a function that cancels the connection by pressing and holding the button when Bluetooth is connected.
The use of this code allows the connection...
Hello,
I want to use FDS with bootloader but i get this error and i'am not sure how to manage it cleanly:
Linking target: _build/nrf52840_xxaa_s140.out
_build/nrf52840_xxaa_s140...
I have done a number of BLE projects using this chip. I am exploring two potential applications which would use the 2.4 GHz radio, transmit only, in a non-standard way. I...
Hello.
I've been asked to help develop an IoT device where GPS positioning and transmitting status via LTE-M/NB-IoT is central. So I've landed on the nRF9160 device, which...
I have a project bord which base on nrf9160, two buttons are set in the hardware circuit, corresponding to the pins of P26 and p15 respectively, and P07 is used as the interrupt...
It appears on the Thing91 reference board that the SIM_DET pin is used to drive the SIM mux control pin. Is that case? Is there more information on how to use this?
Is it acceptable to use the nrf52805's DEC4 pin as 1.3 V reference? I've connected the pin across a ~11 MOhm divider to to create a 0.12V reference for an op amp. I figured...
On SDK16.0.0 + Mesh SDK 4.1.0
I am using a Fanstel BT840X module that has an onboard Skyworks SKY66112 PA/LNA.
I followed the Infocenter guide along with an old example...
