Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello DevZone,
One customer meets an issue. Needs an expert about Matter.
There are 5 Matter over Thread window covering devices which are already commissioned in 2 fabrics...
I am working on a project, in which we are using nRF Connect SDK v2.9.0 on a custom board with the nRF5340 SoC. The device is a BLE peripheral implementing a couple of GATT...
Hello,
I want to validate NB-IoT NTN connectivity using an nRF9151 SMA DK connected directly to an R&S CMW500 emulator.
Goal:
Connect to the CMW500 in NB-IoT NTN ...
I'm having an issue where my device doesn't wake from System OFF (on GPIO or VBUS toggle).
It worked on up to and including nRF Connect SDK v3.3.0-preview1. Doesn't work...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
The ENS210 temperature and humidity sensor connected to an nRF52832 over the I2C interface is not getting ready during initialization. During boot, the ENS210 driver reports...
Hello Nordic Team,
I am working with nRF Connect SDK v3.2.2 on the nRF54L15 DK (cpuapp) and trying to bring up WiFi using the nRF7002 together with the nRF7002-EK connected...
Hello,
I recently received two nRF54LM20-DK (PCA10184) boards and would like to flash the Matter Lock example. Unfortunately, the application doesn't seem to start. I don...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you. And to flash the latest SDK to Thingy: 91x, I need help.
Like how we can flash the...
Hi,
We have onboarded several hundred nrRF9151 devices using the nRF Cloud "bulk onboard" UI (preconnect onboarding using device_credentials_installer.py ). Generally, this...
Hi,
I have an application with 2 SPI IC connected to the same SPIM port of nRF54L15.
These 2 ICs have different SPI mode:
A: SPI Mode 1 (CPOL 0 CPHA 1)
B: SPI Mode...
Hi,
We are working on a custom design for IoT cellular communication (NB-IoT), using the nRF9151. We've done some testing with the SMA DK, and are at the stage of PCB...
Hi. I am looking into measuring radio channels' qualities by using Energy Detection (ED). But for the examples I've tried so far, I've been getting zero for all the readings...
NCSv3.2.4
Is AoA CTE supported in the nrf52811 ?
Product page https://www.nordicsemi.com/Products/nRF52811 says " The nRF52811 SoC supports Bluetooth LE, and is capable...
Dear Nordic Team,
I am working on a custom board using the nRF5340, and I have configured SPI with the following pins:
SPIM_SCK → P0.08
SPIM_MOSI → P0.09
SPIM_MISO...
