Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
I am working on an application targeting the Fanstel BT840X, which combines nRF52840 and Skyworks SKY66112-11 PA / LNA on a single module.
I am using GPIOTE and PPI to drive...
Hi Nordic devzone...
I want to form a ble mesh network through which a Central can reach any Peripheral in the network, if not directly then through other peripheral. The...
Hi,
I'm following the Border Router Quick Start Guide . In it, it states:
To change the settings, edit the /etc/config/thread_border_router file.
However, that file...
Dear experts, please tell me, how can I switch the frequency source for the RTS from STAL to internal RC generator when the processor is running? command sequence does not...
Hello,
im using nrf52832 NRF5 SDK 12.2 , S130 . using the pasted code and i get 1023 on the ADC even voltage is 1.7 volt i using keil ver 5 s130 i double checked the voltage...
Hello,
I have prepared an nRF52840 with DFU example (dfu_nrf52840_xxAA_s140_6_0_0).
When making the DFU package for the blinky example (bin/blinky/blinky_nrf52840_xxAA_s140_6...
Hi all,
I'm working with 2.1.0 version of Thingy:52 firmware (the last version currently). Further I am working on Linux with SEGGER J-Link Commander V6.34c in order to...
Hi,
I want to read register 0x00 (chip ID) of ads1292. i do following...
===========================================================================================...
Hi
I am developing 4 layer PCB for the nRF51822 with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003) with...
Looking to apply an nRF52 chip in a wearable device... ideally without mounting it on a board.
Is that remotely feasible?
It would still be necessary to connect to 12...
Hi to all,
i have a project that was based on SDK 13 and in that version i had a bility to call fds_record_write with multiple data chunk, but in softdevice 14 and sdk15...
I have integrated the code of the multilink into the uart central example. The project can be built without error. however, it is not possible to establish a connection to...
Hi,
I'm starting development of a new product utilizing nRF52840 mcu. We used this chip in previous product with Bluetooh stack (SoftDevice). I didn't participate on this...
Hello!
Since the code of nRF connect code is open (on github) - is in possible to extend supported devices list? In other words, is there any way to use non-nordic boards...
