Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi,
After long time again started working on nordic controller's. Previously my pc was properly configured for NRF5x environment which includes gcc and flahser.
Recently...
The pin connected to lis2dh12's int pin consumes about 300 uA.
But the pin I used as button,also enabled int function , works good.
The pin I used as wake-up is in input...
In order to establish a wireless connection from my pca10056 developing card and a second nRF52840 SoC module using example CLI commands, and then being able to check/set...
Hi,
I have few queries regarding the internal regulators of nRF52840.
1) Is it mandatory to configure the internal LDO or DC/DC regulators of nRF52840 ?
2) If these...
Hi,
As mentioned in the Ch. 5 "nRF52840_DK_PB_v1.0.pdf" Section 5.3 in "high power mode the external supply should be connected to just the "VDDH" pins and "VDD" pins not...
I want to write to nRF52840 the example "ble_app_hrs_pca10056" from nRF5_SDK_15.2.0 by command line.
first I merge 3 hex file (bootloader, softdevice and app) with the command...
Hi,
I'm developing BLE 5.0 applications as a peripheral on nRF52832 under Windows, based both SDK14 and SDK15 (Softdevice S132).
I don't have any smartphone that supports...
Hi every body,
There is a problem with pwm driver example in demo3 part! after downloading, the board led is just on as it must, but after changing top_value there is no...
Hello everyone, I am planning to use the nrf52840 with the ECG sensor ads1298 (AFE for 8 channel ECG). The sensor interfaces via SPI to nRF52840. Has anyone worked on ECG...
Hi all,
I am working on nRF52832, nRF5_SDK_15.2.0, nrf5SDKforMeshv300src, softdevice_6.1.0 and communicate with CAP1214 device.
When I erase all flash on nRF52832 and...
Hello all,
I am using nRF52832 IC, Segger ES as IDE, SDK 14.20 and SD v5.0
I have around 70 bytes of data to be sent to a smartphone. I am using nRFConnect app to check...
Good afternoon. I need to make a network 5 or 6 nrf52840 boards connected as peripherals on a single central board, also of nrf52840. Each board will read a sensor, and send...
because I cannot find nRF module for testing.
and I want to use bluetooth 4.0 BLE with nRF uart
so my product will send data from serial port (rx ,tx through DB9 ) and...
Hi there, We are not using external Crystal for this design and thinking of reusing XL1 & XL2 (Pin 0 and Pin 1) for SPI (MISO & MOSI). But I found that I can't set properly...
