I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
How can I advertise a custom service and the Device Information Service?
I tried the following, but only my custom service is visible in the Nordic Master Control panel...
Hi there,
I'm issuing a STOPRX at a specific time but I'm noticing that more bytes are being put into the buffer from after the STOPRX was issued.
Is there a way to...
Since I've migrated to SDK 10 and updated all my toolchains I've noticed that when I debug on Eclipse, when I run my code nothing happens properly. However if I pause and...
There are various examples in the keil microvision examples for DTM.
The list is below. Is there a difference between these examples?
Which one should we use if our design...
Currently the default for the SPI0 chip select is active low. I would like to change it to active high. Can I do this?
If not can I just have the SPI chip select on a pin...
Continuing with my attempts to get this to work on SES I'm not sure if I'm missing something simple or not.
So using the excellent RKNRFGO (which by the way is much quicker...
There is an error in the gcc makefile included with SDK 5.2.0 that prevents it from detecting when a header file has changed and automatically recompiling the C files that...
Hi all,
I've always been a CSR developer and recently been asked to develop on the Nordic chip. The example code makes sense to me and its not to different to the CSR code...
Hello,
I have a custom board and I am trying to verify the maximum throughput on NRF51822. I am able to communicate with Android BLE stack, however, I need to increase...
Hello! :)
I am a beginner with micro controller programming and want to start with a nrf52
Could someone please explain the difference between the development kit...
Hi,
we have a project in which we have to scan a lot of beacons (up to 100) with Active Scan (scan request and response). We tried to implement this system with actually...
There's an example saadc_pca10036 in the SDK. I am wondering how this piece of code works in that example:
void saadc_init(void)
{
ret_code_t err_code;
nrf_saadc_channel_config_t...
I am working in the SDK10.0 ble_app_uart_c(master),it can connect to ble_app_hrs(slave) successfully.
But if I add a new 128 bit UUID named ACC_BASE_UUID different from NUS_BASE_UUID...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_multilink_central" for reference.
Multi-connection function is OK.
Whenever I connect to peripherals, I can see connected...
