Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
When we test the matter, we sometimes will meet commissioning accessory fail and network dropping. In the worst case, we can't access the network for a long time after the...
NRF_SO_RAI_NO_DATA AT#XSOCKETOPT=1,50 does not cause RRC release as expected, instead hipower LTE continues another ~20s. https://github.com/nrfconnect/sdk-nrfxlib/blob/main...
nRF52840, SDK 17.0.2, SD140 v7.0.1
My firmware application is happily sleeping via calls to nrf_pwr_mgmt_run(), waking up to service interrupts and do work, then going...
I have not been able to get the nRF52840 ncs v2.0.2 watchdog not to reset.
I tried kicking the watchdog every second and can set a break point and see that the kick does...
Hi all,
I'm looking for an SDK function that will tell me if my device is connected to BLE
from this post 8 years ago the answer is no, has something changed in those...
I am using the 9160 to develop a product for the customer. Its sdk version is ncs1.9.0, and the firmware version of the modem is v1.3.1. The device needs to download data...
Since sensor.h API in Zephyr does not support reading hw FIFO, I am planning to use SPI driver to read the hw FIFO on received an interrupt when FIFO has data.
Is there...
Hello
I use nRF9160DK.
Can somebody tell me why it doesn't give an error ( ) if I don't have anything on the I2C line, or how can I be sure if it finds the right address...
I've tested the TX power of nRF52840DKs using CLI application and a sniffer (sniffer device is nRF52840 Dongle). Sent message from one DK to other one via UDP and observed...
Hello,
I am trying to implement the Y-modem protocol to the ble_app_uart example. Basically, I want to send a file from the PC and receive a file in my nrf522840 device...
I use SDK16 with softdevice. Some of its features require hard timings. But it causes hardfault sometimes. It happened at function of gcm_init. My source code is as follows...
Hi
Is there any software that allows to save received Bluetooth data to a spreadsheet? I am using the nrf52 DK running the ble peripheral uart example and received the data...
Hello, after upgrading to SDK version 2.1.0 I noticed that the compilation of all my projects for actinius_icarus_ns always fails:
This is even for projects, where...
Is there a way to initialise a GPIO earlier than in main() without modifying NCS/zephyr code?
We tried an PRE_KERNEL_1 init() function, but this is rather late still.
...
I have two central devices and two peripheral devices each paired with two different services.
I wish each pair can connect only to each other and don't mix up the connection...
