Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
According nrfxlib - modem library - supported features , the nRF9160 firmware supports:
DTLS 1.2 client
TLS 1.2 client
My experience with the TLS client...
Hello,
we have an existing product in "peripheral" role, based on the NRF52832 and soft device S132.
We plan to add support for multi link operation, so that the peripheral...
HI
An example of zigbee multi-sensor is to use log enable info zigbee.report to enable log display. Is there any more information that can be turned on and displayed in...
Hey there! I'm very new to BLE, so I wanted to reach out in this forum to confirm hardware capabilities before I purchase any devices. I'm currently looking at the nRF52840...
hi team,
i am using nrf52840 controller,in my project along with with nrf_sdk.
i wrote a led blicking code using ble protocal on segger IDE 5.40 and i want to see data...
Hi, I'm using nRF52840 in my project. I successfully integrated the BLE DFU service and its characteristics in my firmware, Now I can update the firmware through the nrf-connect...
Hi, we are doing mass production using PLT. And we have found that like 10% of the sensors are stuck in certain stage as seen in following power cycle images.
The program...
Hi,
In the product specification document of nRF52840 it says that in order to read the counter register's value I need to set the capture task NRF_TIMER1->TASKS_CAPTURE...
Hello,
I would like to use the UICR customer registers to store our devices serial numbers.
Can you please point me to some example code for nRF52833 SoC.
I am using...
Hallo Team,
I would like to operate nrf5340 BLE module (BC40C from Fanstel) in "Normal Voltage Mode". Please find the screenshot of the module below. I hope its clear...
Hi,
Just wondering if it's possible, or there is a reliable way to dynamically change the sampling period of the CAF sensor manager module . Specifically the values defined...
Hi everyone!
I am using ESB with the nRF5340dk without ACK, but from time to time need to send a packet with an ACK request in order to send some commands from the receiver...
Hi,
After successful building of pca10040_s132_ble_debug example with changes to project :
- excluding SEGGER_RTT_Syscalls_SES.c from build
- from flash_placement.xml...
Hi,
We are hoping to send our samples for CE certification. We use nrf52805 IC in our design. We do not use any precertified modules.
Looking at the Direct Test Mode folder...
