I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi,
I need to connect nrf52833 (BM833 module) with host controller. what are all the interfaces needed to communicate with host controller? help me out in this.
Kindly...
I used 2 channel saadc, channel 1 and channel 3.
Maybe in the first few minutes, it's done ok,
p_event->data.done.p_buffer[0] is belong channel1 adc value
p_event->data...
Hello,
We have integrated the FATFS example as shown in the usbd_msc example project into our own firmware application. It works perfectly on the nRF52840dk and when we...
Hi,
I want to check time line of my project using segger SystemView.
- SDK 16.0.0v
- ESB example
- nRF52832
When Start recording, "Could not find RTT Control Block...
Hello Team,
I want know how to use RESET pin [pin. no. 21] as a GPIO.
I followed below thread but it not work for me!
devzone.nordicsemi.com/.../disabling-pin-21-of...
Hi:
What's the marking on the nRF24-LU1+?
Marking exactly "nRF24-LU1+" or any chance marked as "nRF24-LU1" instead? Your big assistance & prompt feedback is much appreciated...
I am using NRF52810 in : In advertising mode not able to erase or write to flash sd_flash_page_erase. hungs up via processing commands from nrfx_twis_state_machine
Hi,
I'm developing a custom application starting from ble_hrm_freertos application. When NRF_LOG is enabled there is no way let the chip in low power consumption. I found...
Dear Technical Support,
I have faced a problem debugging firmware on our custom board based on Nrf52811. We use j-link EDU and Segger Embedded Studio as development tools...
Hello Nordicsemi community,
1) manual build of mcuboot - When trying to build the mcuboot for nrf5340 via the mcuboot/samples/zephyr via the west build command, the build...
HI , nrf52832 with SDK v16 on that using this nus example location below mentioned
examples\ble_peripheral\ble_app_uart\pca10040\s132
in this example, didn't change...
Hello,
I have recently received the nrf5340 development kit as part of the Hackster contest.
I followed the webinar and to get started
1. Connected board via micro USB...
I started a new ticket since I got a solution to not connecting to the cellular network. Apparently the iBasis sim is not working so I acquired a Hologram sim. I now can connect...
the code yesterday when debug can pop out voltage ,i do not chang anything today ,the code can not run the location ,i make three breakpoints in code and debug ,the code only...
First day using the new dev kit nRF52833-DK. Connected it up following the instructions on nordicsemi.com/start52833dk - computer won't mount the JLINK removable disk so I...
