if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
nRF52840, SD140, SDK 17.0.2
We're using UARTE to communicate with a peer MCU. We're using hardware flow control (CTS and RTS are enabled) and the baudrate is 115200. The...
Hello,
I'm using two nRF5340 MCUs with BLE5.2 audio in an application. I had a couple questions I hoped the Devzone could help answer.
1. On one of the MCUs, I was originally...
sorry for the perhaps stupid question - but despite several hours of intensive searching, I am not getting any further with the start -up of my new and beautiful Thingy91...
I do not understand how to compose these settings.
Using ncs v1.5.0 GPS sample with SUPL enabled.
This works OK on nrf9160-DK using the supplied settings
#define AT_MAGPIO...
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/61935/bootloader-flashing-error---nordic-nrf52840-usb-dongle I get the following error:
DFU failed: Error message...
Hi,
I’m trying to measure the current on NRF52840, SDK 17.0.2.
I have modified the HeartRate Measurement example’s advertising parameters as PLper my requirement.
...
Hi,
I am trying Zephyr for 52840 dongle. I am able to west build, but could not west flash.
While I do west flash, I get
-- west flash: rebuilding ninja: no work...
I bet you get sick of this, but I've looked at the other solutions and followed any advice, but no joy.
I am trying to use a Makerdiary nRF82540-MDK usb dongle to evaluate...
Dears,
When Reset pin(0.18) is used for QSPI (GPIO macro is not defined as RESET), after initialization ,Jlink is disconnect.
Would you please suggest it? Thanks.
I am using a nRF52840 dongle and want to filter ADC raw data. I have downloaded the CMSIS 5 DSP package.
And tried to include a copy of an example (arm_fft_bin_example_f32...
I found that AGPS can get location information via mobile network. With this feature "GPS" can work indoor.
1. Thingy91 also uses AGPS, but when I ran prebuilt hex asset...
Hey all,
I'm trying to install the nRF Asset tracker. I'm stuck at a step called Building the project using GitHub. I just need to know how to build the project using...
Hi,
I was trying to retrieve the log information from the Nordic to the AWS server. I can see all the log info with the Status as Error. I'm retrieving the logs from...
Dongle cannot enter reset mode, and led is not pulsing(no shine ) when I connect to PC, the device cannot detect it,too. Is their any problem on the firmware, the device cannot...
Hello there,
I am trying to find the datasheet from the device NRF31502 F but I am having some trouble!
Can someone help me or point me where I can get it?
Thanks
