if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I am looking for detailed electrical characterization details for SAADC - beyond 1 page summary in nRF52833 product spec v1.3; under 6.21.10.1 SAADC electrical specification...
Is there some documentation listing what C library functions are supported? For example if I use the Keil IDE to look for FILE I find it. But if I look for 'fread' it says...
Hi,
I'm building a gateway using nrf mesh serial, and I want to monitoring devices status in the network by listening heartbeat messages from devices, but when I set publication...
Dear All, We will do a production with over 1000 Nordic nrf9160 devices, for which we need to program the modem firmware (v1.2.0) and the application software. We would like...
Hello, I started learning BLE/nrf about a week ago and I faced an issue that I unable to handle more than one connection simultaneously.
I have a pretty simple application...
Hi,
I am using nRF52832 and SDK v15.00 for development.
I am working in ble_app_uart peripheral example. I have a task where I need to configure another UART communication...
Hello Everyone,
we are using Nordic's nRF52840 controller with SoftDevice S140 and the default Bootloader(C:\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10056_ble...
Hello, I am working on a nRF52840 and started with the SDK15 gls bonding example. The device has no buttons or display so we are stuck with 1v2. We are hoping to incorporate...
Dear friend，
I want to implement ota data packet request through my own code. In the \examples\zigbee\ota\client example, line 876-1268 of zb_zcl_ota_upgrade.h finds the...
Hi there,
I'm using a nRF52-DK for a while, but now I made a bad misstake: overwrote the interface firmware. I pressed accidentally the RESET button and flashed a wrong...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
Hi all,
I have two questions about BSP buttons management.
I see that the BSP supports the short press and long press for a button. However it seems to handle only one...
Hello
I want to read the values of two potentiometers from the Ain0 pin and the Ain1 pin through SAADC.
I could easily read one value through the saadc example, but I...
Are you able to enable internal pin pulls for UARTE pins, specifically the selected RX pin?
On page 490 of the nRF52833 datasheet, footnote '35' states that "High baud rates...
