hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I can't get the Master Control Panel to work. I think the drivers might be messed up but various re-installs aren't having any success.
Can you suggest some troubleshooting...
I'm Dinesh Katkar, trying to adapt
new IoT design and development and planning to build wearable device based on nRF52832 Bluetooth SoC chip and ordered nRF52 Development...
Hello,
I am new to all this RF stuff. I am trying to set up multiple transmitters (2 for now) and one receiver. Basically, each of two transmitters read one set of data ...
hi all,
i am currently using version 8 sdk.
i tried to include bsp_init() function in my code.
i attached following header files
#include "nrf51.h"
#include <stdbool...
When exporting the example project BLE_HeartRate from the online IDE to the GCC (ARM Embedded) toolchain, the makefile fails to compile.
First, the compiler throws "fatal...
Hi:
I am using nRF51 Dongle to develop my platform, and software is base on esb_low_power_prx and esb_low_power_ptx in nRF5_SDK_V11.
For production, I need to program...
When I connect to another beacon using sd_ble_gap_connect() scanning on my device is stopped. I have to wait till connection is established or establishing connection fails...
The Nordic set comes with a Device number of it's own. I want to overwrite that device number, or store a device number in a different location in the EEPROM. Is there any...
What files within the FDS are used by the modules of the Nordic SDK?
For example, I know that the Peer Manager uses the FDS as a storage backend. I need to know what files...
Previously I implemented a DFU bootloader. It works fine on s120 softdevice.
But after I ported it to s110 v7.0 softdevice, it can not work. After investigation, I found...
Hi,
i just followed the steps for migrating to peer_manager - as lines out in the tutorial.
However i will never ever get a callback to pm_evt_handler.
I am trying...
Hi,
I am facing some issues on the Android part of the BLE.
Firstly it takes around 20 seconds for the android phone in scanning mode to find the nordic board. This...
I encountered the following error while adding device manager to ble_uart_app in SDK_11 s130 using the hardware nrf51-DK. I'm using Keil compiler.
._build\nrf51422_xxac_s130...
While using the device manager, I encountered this line;
#define SEC_PARAM_MITM 1 /**< Man In The Middle protection not required. */
Since security is important, is...
Hello!
I'm trying to test several types of ANT communication like broadcast, background scanning, etc.
And When I check ANT broadcast rx example, I realized that some...
