Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I need to read the registers of the KTD2026 IC as specified in the datasheet.
In short I have to send a read command with the device address (0x30), the address...
Hi, I'm working on a BLE peripheral project using nRF52840 with nRF5SDK version 17.0.2 and softdevice S140 version 7.2.0
We are considering to increase our full device name...
We are starting a new design that requires a LTE-M chip. Upon comparing features between nRF9160 and nRF9161, I see 2 differences
DECT NR+
3GPP Release 14
First...
Hi,
I am reading through different Nordic documentation. In some documentation, it shows a first stage B0 Nordic bootloader. This bootloader then can point to MCUboot...
HI,
I have a product which scan for RFID card through NFC and Mobile Device through BLE after nRF52840 MCU was wakeup.
If I scan NFC and BLE scanning separately, everything...
Working with a Pinnacle 100 using an NRF52840. I have a HMI with a TTL serial interface. I have verified I/O on the HMI itself via a TTL/USB converter to Tera term, but having...
Hi! I have a fleet of narrowband and cat-m devices around the world. I want to determine their rough position by using the cell tower information. I tried CellLocate from...
I have a board with the nRF52832 and a board with 12 SK6812 LEDs on it in the shape of a ring. I have code that sometimes will display the correct color on the ring but other...
I think the NFC pin is set to the default state on the nRF52832.
Currently, I set CONFIG_NFCT_PINS_AS_GPIOS to 1 to use it as a GPIO pin, but is there a way to make it the...
Hi, I'm using nrf52810 ,nrf connect, zephyr, vscode extension. I’m having trouble using both UART0 and the NUS UART service. Here’s a snippet from my overlay file:
/ ...
Hello everyone, I'm trying to perform a device firmware update using the buttonless service on nRF52DK with SDK v17.1.0 and Softdevice S132.
I can connect correctly to my...
Hi,
I’m working with Timer 0 on my nRF5340 DK and trying to set up two different intervals: one at 1 second and another at 60 seconds, each on separate channels (COMPARE0...
If I am to do a custom SPI Slave driver to achieve ultra low latency handling and would like it to coexist with NCS / Zephyr, is there a document describing this ?
E.g....
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it is iBASIS...
