In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
We are developing a sleepy end device using the nRF52840, using light switch sample . The end device is connected to a Zigbee coordinator, also based on the nRF52840.When...
We are using a 5340 with a Skyworks 66112 FEM. Below is our hci_ipc.overlay file.
We are setting CONFIG_BT_CTLR_TX_PWR_ANTENNA =20. When we measure the output of the FEM...
I'd like to use playback feature of PWM. There is NRFX function for that: nrfx_pwm_complex_playback(). This function, like other NRFX drivers, needs appropriate instance structure...
My Win10 app - needs to connect to an NRF52 that is using the "NuS" Service - and I can't use the WinRT or dotNET.
In this post: https://devzone.nordicsemi.com/f/nordic...
Hello,
Thank you for reading my question. My company and I have developed a BLE device for use with windows computers based on the nrf52810. The device pairs with windows...
I'm building my zephyr project for nRF5340, using west.
However, each time I change my code and re-build to try it, my PC (which is pretty recent) takes around 40-50s just...
Hey.
I have a problem where the task watchdog times out immediately.
I have taken the samples/basic/task_wdt sample and modified it a bit to simulate what I have in...
The environment setup I'm using is VsCode with the NRF extension. I'm using SDK v2.6.1. When flashing bootloader firmware to my device I get this output on my vs code terminal...
minimal_log % west flash -- west flash: rebuilding [0/4] Performing build step for 'mcuboot_subimage' ninja: no work to do. -- west flash: using runner nrfjprog Using board...
We have fairly regularly observed that the reset reason register gives two reasons for reset: software request and watchdog.
Is it plausible that these bits are genuinely...
Hi,
I am trying to communicate with nPM1300 PMIC board using NRF5340DK. I have made the connections and set up the overlay file as recommended. The I2C write (i2c_write_dt...
I am currently developing software of the nrf9160 and am having trouble with a firmware upgrade. The firmware data is received via UART. All of the functions work as expected...
Hello all,
I am working on a ble application on zephyr. I need to send a notification on a specific characteristic.
If I call bt_gatt_notify from where I want to send...
We're currently using a virtual operator as carrier, so our device is roaming in Finland. It seems that Elisa (24405) is the preferred network, but the data plan is restricted...
Hello, can 2.0nH or 1.8nH inductors be connected instead of the 1.9nH inductors connected to the ANT1 and ANT2 pins shown in the NRF21540 reference circuit?
