Hi,
I am working on BLE on nRF52833dvk, am able to execute the sample example . I have one of the requirement, that I need to write the unit test cases for Bluetooth for...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi everyone,
I fill a bit surprise but I don't understand who the speed of the gps is working :
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications...
Hi, can someone provide an example of reading the device ID from an QSPI flash (NOR)?
I'm trying to get it using my NRF52840 using the nrf sdk17.1 with the flash IC AT25FF081A...
I see in the datasheet that the NFCT peripheral supports wake-on-field, but the application I'm interested in is to upload/emulate an ID number to the NFC tag, and then hours...
Hi
I need to reball some aQFN73 nrf52840 devices and I couldn't find the specific ball size in the product spec document Nano_BLE_MCU-nRF52840_PS_v1.1.pdf
Can someone...
Hello,
We are currently working on a project where we need to sample a frequency input on a GPIO pin up to 6MHz. I have tried GPIOTE and TIMER with a PPI channel, but can...
Hi! We are currently in the process of migrating our nrf5 SDK code to NCS, on nrf52833-based hardware. After being stuck for a while on the basic init process of MCUBoot,...
Hi
I am reading the exernal power in one ADC channel and the backup battery in other ADC channel. When my hardware has not external power and the backup battery drop until...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
Your old documentation website ttps://infocenter.nordicsemi.com/ carries a banner saying it will be shut down on 18 June 2024. Please don't do this! I can't find equivalent...
I'm running NCSv2.6.0 on some custom hardware, with an nRF52832 IC fitted. I'm trying to trigger an ADC measurement every ~ 300usec using a Counter, so need to set the Counter...
Hello community,
I am working on a custom nrf5340 board design, that uses the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module...
Hi,
I've attached the steps performed to install the mosquitto bridge and getting errors on yarn deploy
Also see attached steps, I believe I have done everything correct...
I have recently upgraded my SDK from NCS V2.2.0 to V2.6.0, and have come back to some firmware I had working under 2.2.0 as I need to progress that. The firmware is based...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...