Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
I'm thinking to have a cental_and peripheral at the same time.
Using the the standard ble I have to setup the configuration.(Who is the Central_uart and the Periheral (...
I'm profiling the current consumption of our device, on an nRF5340 module, at SDK 2.1.0.
So far as I can tell, the ADC is using approximately 1000 uA. It's sampling via...
Hi,
I'm using PCA10100, and developing my project on examples\ble_peripheral\ble_app_uart(SDK 17.1.0)
I connect P0.08_8 and P0.06 with other sensor module's uart, when...
I'm developing a BLE application on the nRF52832 that uses NRF_SDH_DISPATCH_MODEL_APPSH to receive events from the SoftDevice. My application involves using some software...
Hi, Nordic:
I am trying to use spi to transfer data between the two DKs. But I'm having trouble emulating the use of spim to use spis.
This is my main.c.
And this...
In the nRF52840 datasheet, peripherals don't appear to have shutdown or power-off controls but they do have enable/disable registers. I'm guessing that Device PM turns on...
Hi, I use periodic advertising to send live data based on readings from an accelerometer. I want to change the advertising packet after every advert to the new values.
My...
Hi there,
I am currently building nrf9160 custom board. But now I am planning to implement provisioning credentials like this URL https://docs.nrfcloud.com/Devices/Security...
Hi
The response to this ticket
says "You can implement active RFID. In active RFID you can for instance periodically wakeup the chip to turn ON the radio for a short...
Does Nordic provide a DTM application for the nrf5340 which communicates over the USB interface as a COM class instead of using a UART interface? It's been brought to our...
Hi Nordic team,
I debug on the board, and I want to check the connection at the first time without connection before. so I want to clear data on the flash first, then...
Dear Nordic Experts,
Is there any way to detect the the WDT has reset the system. I mean some WDT register from which you could read this information, and that would be...
Hi,
I use nrf5340 with nrf connect SDK 1.9.1
I found some issue when: 1. My peripheral device that running connected and paired to some Central device.
2. The central...
Hi guys. I was observing the PCA10121 PCB layout using this link.
From Murata SWF connector datasheet, it says
https://www.murata.com/-/media/webrenewal/support/library...
Hi,
I am using NCS 2.1.2 with the [email protected] (but I have tested with 2.2.0-rc1 and it doesn't change anything). I have attached a simple example which should just...
