I'm having some issues regarding the data update interval when running the asset_tracker_v2 application, particularly with adjusting how frequently it publishes data to the...
Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hi, While I'm aware that the specs are not yet finalized, are there already any hardware requirement estimates for running Matter over Thread for a battery powered node? I...
Is it possible to perform an over the air update via Bluetooth Low Energy while the sensor is connected, but the app is running in the background? If this is possible, are...
Hi,
I found that when my custom board spend 201 ms to boot up. Because I can't change my board, I am looking for reducing time to boot up.
Do you have any idea and how...
Can you please tell me why I get an -ENOTSUP error when I set the scan .timeout parameter to anything but 0? Is the suggested workaround to use RTOS functionality to timeout...
Hello All,
I have the following issue - a peripheral and a central using nrf52832 with SDK 15.3 and S132 - on the peripheral I advertise with a whitelist - the central scans...
nRF Connect used to work fine. After the 3.8 update it could no longer see devices. At that point a re-install helped.
Then after the 3.9 update it stopped working again...
Dear support,
I am using nRF52840DK (PCA10056) and nRF5 SDK version: nRF5_SDK_17.0.2_d674dde. I am trying to make all the prints in my application to be displayed properly...
I working with the MDBT42Q-DB with the nRF52805 module. I've started from the ble_app_beacon example in SDK 17.1.0. I was able to compile and run the example in Segger Studio...
Hi.
I used sdk 1.4.0 with nrf9160, I used UART2 to comunicate with another mcu. I run fine and no problem.
Today, I update to SDK 1.6.0, I edited UART2 ( in device tree...
The RTC irq_handler of the latest nRF5 SDK may cause potential problems.
Imagine someone trying to extend the RTC timer from 24bit to 32bit, the developer has to keep an...
Hi All，
The version of Wireshark I used is 3.4.0.
The version of Python I used is 3.6.7.
Packet capture device uses nrf52840 chip.
After installing Wirkshark and related...
I'm working on nrf5340 DK and I wanted to use a mic for sound detection. To do so I installed the X-nucleo-IKS02A1 shield on my board because I have seen that it is compatible...
Hi - I'm using a nRF52840 DK for the first time with my 2010 MacBook pro running OSX Sierra version 10.12.6. I have SEGGER Embedded Studio for ARM 4.12 installed and Segger...
Sometimes, the output of the NRF_LOG commands does not make it to the RTT viewer.
The output of such commands as NRF_LOG_INFO() and NRF_LOG_DEBUG() and NRF_LOG_HEXDUMP_DEBUG...
I design with reference to the evaluation board (nRF9160-DK). What kind of resistor (R4) is used for the input circuit of the GPS antenna? The manufacturer and part number...
