Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I am trying to code an AoA transmitter using the direction_finding_connectionless_tx sample project as a basis. I am using nRF Connect SDK v1.6.0 with nRF52833.
I am...
Hello,
I am having a few problems when trying to check if the nrf52 is dfu mode with my python script.
For that i was trying to get the firmware version from the dfu...
On Mac OS X Big Sur using the nRF Connect 1.6.0 installation in Segger the documentation suggest that to add a new source file to a project one should right click the project...
Hello, I tried to run the following command on my nRF52832 today and it reported an error.
The operation before the error was: I enabled APPROTECT, and when my colleague...
Hi, I made a mistake while working with a custom board.
I run "nrfjprog --recover", which obviously clears UICR, and then I powered the board off without writing the new...
I have a custom board with 3 nRF52840 chipsets, 1 central module is connected to 2 side modules.
The central module communicates with each of the side modules using UARTE...
Hi!
There is an end device that measures the temperature. If I calibrate the ADC during initialization or immediately after startup, the program hangs. If I start the calibration...
Hi Team,
I am trying to make RTT in debug terminal instead of debug serial port i was add all rtt files in the project tree but it was not shown in cmsis configure wizard...
Hello everyone,
I am trying to implement ECDSA_P256 in my code by using the nrf_oberon libraries.
What I have to configure in order to use these functions?
Regards ...
I use nRF52810 SoC to forward data between BLE and UART on our product. So I initialize UART interface and set some GPIOs once enter the "main" function in my codes. But we...
Sdk: 1.6
Modem fw: 1.3
Hi,
I am testing the GPS + supl example on our custom board. I am sitting indoor close to a window so satellite reception is affect.
the example...
Hello,
I am Working on the nRF52840 custom board.
To drive the motor and buzzer I am using a PWM driver in that when I set duty-cycle 20 percent then the output of PWM...
Hi guys,
Using the PPK 2 board I have noticed that sometimes my device does not go into deep sleep mode between two tasks. I had to implement a lot of flash operations using...
Hi Team,
Currently we are using 52840 soc with softdevice s140_nrf52_7.0.1_softdevice.hex.
We want to migrate to 5340 for BLE 5.2 features, we would like to understand...
Hi,
I need the SAADC of the nRF52840 to do the following:
It should sample two channels as fast as possible for a certain time (or for a certain amount of samples)....
