Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
NB-IoT Dual HARQ and Max TBS size enhancement brought in Rel14 (Cat-NB2): on nRF9160 it was controllable via AT%REL14FEAT, using parameters <NB_dual_harq_support...
Hello,
One question on the Reduced Mobility feature (3GPP Relaxed Monitoring TS36.304 and Nordic-proprietary feature) based on %REDMOB command.
AT manual says :
%REDMOB...
AS-RAI (RAI over Access Stratum ; Rel-14) over LTE-M was available on the nRF9160 via the command AT%REL14FEAT (option <as_rai_support> e.g. AT%REL14FEAT=0,0,0,1,0 to enable...
With the current version of nRF Connect for Desktop I received an error when updating the Toolchain Manager.
I then uninstalled the Toolchain Manager and tried to reinstall...
Hello,
Although my board is not equipped with an external LC filter, I flashed firmware which enables DCDC and this made the chip unresponsive.
Is there any method...
Hey
I'm trying to figure out what is the intetned way of using the tools for configuring a project.
We have the following config files in the following structure:
...
Hello I currently have an error when flashing with j-link on a custom board. The mcu is nRF52833 QDAA and the debugger pin is connected to 4 pins. In VSCODE, CONNECTD DEVICES...
I am working on a pdm microphone INMP621. I am getting the pdm data using nrfx pdm drivers but not sure about the logic which I am implementing to convert pdm to pcm. I read...
Hi, I need a little help with mcuboot.
We want to transfer firmware updates via CAN (MCP2515), which is already implemented. Was we are short of time, and we want to integrate...
We have a design using a nrf5340 with a Renesas Wifi chip, That Renesas chip uses a 1 wire interface for Coexistence
We are using Zephyr 3.5.0 and have tried to follow https...
Hi, I have Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H for getting sound and for driving output via speaker I have tas2x63EVM amplifier. Since the nrf5340 audio dk...
Hi,
We want to have some RF-PHY tests on nRF52840 DK.
Therefore, I need a HEX file to make nRF52840 DK get into direct test mode and communicate with CMW270 with UART...
Hi,
I am currently testing the HID Keyboard example in SDK17.1.0. When the nRF52832 is connected to the computer and the Caps Lock key is toggled, it prompts "CAPS ON" or...
I tried to install nRF Sniffer. I followed the instructions here: https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-ble-sniffer/guides/installing_nrf_sniffer.html I...
