I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
using west update i just update the old version 3.0.2 to 3.1.1 and after take blinky code and build then i have got below error,also using the vs code i doenload the NCS v3...
Hello, While designing the hardware circuit for the CAAA WLCSP with internal LDO regulator setup on the nrf52810, I removed the 32.768kHz crystal oscillator and retained only...
I am currently developing my project using the nrf52832 and the nrf5SDK.
I utilized the peer_manager module, and in the application, when being connected as a peripheral...
Hi,
I’m using an nRF5340DK with nRF Connect SDK 2.9.1 , configured as both Central and Peripheral with the nordic SDC running the network processor Goal: allow the board...
The High-Performance Framework (HPF) is a framework designed to support the development and integration of software peripherals using coprocessors (e.g. FLPR on RF54L15)....
Hi,
I managed to get Channel Sounding with Pixel 10 as Initiator working, based on this change on mainline.
https://github.com/nrfconnect/sdk-nrf/commit/30f67fc0b6be8051b5d8f73d900675dd98758631#diff...
Hello Nordic team,
I'm developing a BLE peripheral using nRF52833 and would like to validate that my approach for handling connection parameters aligns with Nordic's best...
I now need to make a program on nrf5340 audio DK, SDK v3.0.2 to scan extended adv and print the BASE information in the subgroup in PA, without sink BIS, besides, a smartphone...
Hi,
I am following the course "nRF Connect SDK Fundamentals" and am almost at a standstill when it comes to progress.
I am still struggling with lesson 1 and lesson 2...
Freshly installed VS Code natively on Windows (also tried on Linux and WSL with same result) with NRF Connect Extension Pack, SDK 3.1.1, Toolchain 3.1.1 was used to create...
i get various answer about this, been in the rf design for a while, we used to make global antenna lenght on some give am ook circuit a tad shorter and then use a load cap...
Hi Nordic
I am working with nrf52840 and nrf52832 using ncs v2.8.0
I am trying to save coredump to flash according to instructions on this link - https://docs.nordicsemi...
Hi everyone,
I'm working with the nRF52840 using the nRF5 SDK v17.1.0 and SoftDevice S140 v7.2.0 . My application uses QSPI for external Flash communication.
I have some...
Hi,
i just noticed that for the nRF5340DK board, the file nrf5340_cpunet_reset.c has been removed.
Nevetheless it is still reference in the documentation online: https...
Hello,
We have built a device that uses the nRF52840 reference design shown below. With the configuration shown the board advertises as expected. If we replace either...
