Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
HI Devzone
currently my customer would like to get SRAM execution permission in their porject.
we found a config marco to set the SRAM permission " CONFIG_SRAM _REGION_PERMISSIONS...
HI,
i using 52840DK SDK17.2 s140 10056 test NFC pairing.
ble_central\experimental\ble_nfc_pairing_reference_c 10056 s140 ble_peripheral\experimental\ble_nfc_pairing_reference...
I am using
MF V1.3
NCS V1.6.0
nRF9160Dk V0.15.0
Project: AGPS Sample
If i set the Interval in the gps_config structure to any number under 240 and run the sample...
Hi,
We are working on nrf52840 in that we have some doubt how to test the radio tx and rx in datasheet you have mentioned
Active mode Tx Current - 4.8mA and 0dbm ...
Upgraded from v16.0.0 to v17.1.0 and have a truncation issue. It only occurs after the first send. Reverted back to v16.0.0 and all ok.
No other code change other than the...
I've searched around, but i couldn't find anything about how to use DMA with SPI master on a nRF5340 (and zephyr doesn't support DMA on nRF5340 right?). Can someone point...
Hi,
I'm using ble_app_uart to test AT.
When I sending a buffer
reset_buff[10]="AT+RESET\r\n";
RTT log showing an error
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at...
Hi all,
I'm currently trying to interface an nRF52832 with an external Flash chip via SPI
I have tried with both NAND and NOR types, specifically the MT29F2G01 from Micron...
I am trying to develop CAN communication using nRF52 dev kit based on nRF52832 (PCA10040) and a MIKROE CAN SPI click 3.3V board . This board has an mcp2515 stand alone CAN...
Hello,
I had RTT configured as the logging backend and it was working fine. When I enabled the SHELL on RTT, the log output stopped. Maybe more specifically, printk() output...
Hello there,
I'm trying to downgrade nRF Programmer from v2.0.0 to v1.4.11 as it is not possible anymore to select a Segger debugger as target device in the newer version...
Im trying to make a simpel project reading the sensor BME280 over SPI. I can´t get any activity on the SPI pins when i check with my logic analyzer.
I´m using nrf9160-DK...
I've based my code upon the HIDS keyboard example and added code to support an attached polled sensor with I2C interface. The device will pair with the Android phone just...
Hello,
I'm writing an application that sends cycling power information via ANT+ and Bluetooth (S340, on a nRF82840). While the ANT+ is a pure cycling power service, the...
