SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hello, I am using NRF52840, I tried to use Jtrce for debugging but the results are unreliable due to design of the nRF52 target device in regards to the trace clock speed...
Project context: -------------------- Server BLE for home trainer diy Target (Bluetooth server) : Bluefruit nRF52 The feather Library : BluefruitBLE Client : nRF Connect ...
Hello,
I am in the process of writing a custom application for a custom board for the nRF5340, but have run into some odd behavior with SES when I started changing around...
Hi,
SDK 17.0.2
I notice a startup current sequence (shown below) which is consuming around 8.3 uJ. I would like to know what operation on startup is causing this surge...
I've added:
zephyr_code_relocate(src/main.c SRAM)
and
CONFIG_CODE_DATA_RELOCATION=y
However, this only relocates by main to RAM. Vectors, kernel, etc, are still going...
Using 52840, I would like to drive an ADC chip - and it needs to get 800KHz. sampling speed (800/16=50KHz) should be accurate
* a timer isn't an option - not accurate enough...
Hello,
I have a Thingy91 which was previously successfuly paired to nrf cloud. I deleted the device from nrf cloud and provisioned new certificates from nrf cloud (and uploaded...
I am trying to set up a peripheral connection between an nRF-52840 and an iPhone via my team's iOS app. The board connects normally via the Nordic Connect app and shows the...
I have configured the server with max mtu size of 512 and changed the start location of the app to allow for a larger SoftDevice. I have done this both for an mtu of 512 and...
In one of my projects, UART interface is used for the communication of external sensors. During the power consumption test, I found that when 9160 enters the idle state, its...
Hello,
I am having nRF 52840 SDK for which I am able to control leds of sdk using ble app blinky example through android mobile.
Mean while, in nRF mesh provisioner example...
I'm having a bit trouble here getting migrated to LPUART on a working nRF9160 <> HCI BLE on nRF52 (On the Thingy91). As far as I can tell my .conf and .overlay files are what...
Hello,
I've run into a problem, which seems at least to be similar to that described in another thread . In short, if I set up a counter with CC[n] and start it, a COMPARE...
Hi,
I would like to store important information (few MAC addresses) in flash memory at manufacturing stage. Then my program will be able to read these information thanks...
Hi ,
My environment:
nrf5340 DK board
nrf connect SDK v1.5.0
segger Studio IDE
I would like to establish communication from application core to network core...
