Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi, I want to power the system off when a a characteristic is written. I do so by calling sleep_mode_enter function listed below. When sd_power_system_off is called the system...
hi
i program the hex of nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard into pca10056,it run ok .if i don't connect it by phone，and than press button1...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hello everyone, recently i was trying to figure out the best way how to send a large amount of data from ble peripheral to the central (Android device in this case) and thanks...
Hi,
I want to add FDS basedon dimming_serve example ,However,after fds_init(); it not jump to fds_evt_handler but stop wait .
The below is my code:
And The Bellow...
Hi all.
First I would like to apologize for any mistake because I'm posting first time here.
I'm using Visual Studio Code (VSC) to evaluate the blinky example from nRF5...
I recently had the need to communicate with a device over I2C. I'm using the nRF52 as the master. Everything works fine, but power is a concern. I am putting the processor...
Hello,
I have the same problem as this post . The difference is my SPI is sending out junk instead of stucking. I have tried the solution in the original post but no avail...
We bought 3x nRF52833dk (pca10100). Because the nRF5SDK V16 has only a few pca10100 examples we searched this forum and followed the advice: Change the "Linker->Sections Placement...
Hello,
I'd like to look at the Zigbee network traffic to/from/between IKEA Trådfri devices, but am unable to see any traffic when using nRF Sniffer from Wireshark. Unfortunately...
Hi,
I have an nRF52840 Development Kit, and am trying to control an IKEA Trådfri bulb. I'm following the commands from the SDK documentation , but it feels like they're...
So I'm trying to write a value to a characteristic I have set up as in the code below (figure 1), using the code further below (figure 2).
The sd_ble_gatts_hvx call is coming...
Hello
I would like a suggestion on the best architecture to collect data from multiple sensors in a room. Let me explain my need.
I have a room where we place multiples...
I'm trying to understand how RSSI measurement works.
According to datasheet if I understood correctly I have to issue a " TASKS_RSSISTART " command and wait for the corresponding...
