Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Dear All
I want to advertise as broadcaster (not peripheral and also not as a beacon). Advertising packages do not have the information nonconnectable and even if I am using...
Hi,
I'm working through a number of the PCA10040e examples (SDK16 | S112 | nRF52810 - mouse and keyboard to be specific) and have noticed some irregular behavior when waking...
I have the nRF connect application running, but it shows 24 channels, most blue and 3 green. What is the significance of blue vs green? Also, even though I have wifi turned...
I have recently started understanding nRF52840 using SDK v17 and soft device S140 v6.0. I'm using Keil as my dev environment.
Opening any of the SDK example in Keil, when...
Hi,
I am trying to integrate ble based bootloader into my existing system running on nrf52840. I am using SDK 16 v7.0.1 with sd140. To test the process, I have added the...
Hi, I am working on the ble_app_template project. 1-How can I enable simple pairing without NFC? 2-Also how can I set pairing code? 3-Is the write way to secure characteristics...
Hi, I am developing the project where to read the sensor data and send the values to the mobile application as User Interface. I have built the Board with nRF52832 and using...
The size of the FIFO is sufficient. The value is extracted from the FIFO after being received by the UART. Repeat UART reception.
APP_UART_FIFO_ERROR occurs in the above...
Hi everyone,
I'm using SDK 15.0.0 S132v6.0 and looking for a way to get an event when the advertising times out. I discovered the softdevice_ble_evt_handler_set() in this...
Hi,
I am developing a device based on the PCA10059 board, SDK v15.3.0, and softdevice v6.1.1, and I want to imply that I am using the FDS module with 20 pages in my firmware...
Even after I get a license for the Nordic stuff, SES won't show an installed activation:
The license "installs" fine though:
And I do have the "Nordic" version...
Hello,
When I try and use nRF connect Programmer to update the modem firmware via USB it fails each time in the second step (Modem Firmware Update) with the error message...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project, which acts as a central, and an IOS phone as a peripheral. I have a read/write...
I have an nrf52833 wired up to 25 switches and detect changes via the pin SENSE configuration triggering the GPIOTE PORT interrupt. My interrupt handler: 1. reads the pin...
Due to whitelist limitation of 8 peers, I am doing manual filtering of bonded devices. I am trying to use pm_address_resolve function to figure out whether I have previously...
